cat5 cable comb 3d models

Cable comb for 8 pin (4+4) PCIe sleeved cables up to 3.2 mm in diameter. I recommend making sure settings in printer allow smooth edges for a better look and to prevent cable damages with rough edges. ...I printed this in three different positions, on...

Moin Moin, a cable comb for the bequiet! 20+4-pin ATX cable (Power Cable CB-6620).I think it only works with the specified bequiet! ...cable because they use a different thickness and some pins are occupied with 3 cables.Scale to your needs.Hope you...

This comb makes it easy to arrange the wires in an Ethernet cable to fit into an RJ45 connector. The comb holds all eight wires in place while you check the correct order. The wire spacing is slightly wider than inside the RJ45 connector, but the...

Here's the original link: https://www.myminifactory.com/object/3d-print-cable-comb-for-gpu-8-6-pin-6601 Print this cable comb at 0.2 mm layer height with 10% infill. It will use about 1 g of filament and take around 5 minutes to complete. ...Happy...

A simple cable management comb for ZWO ASI cameras with a 90mm diameter.  Fits snugly over the camera and provides support for cables coming off the back.  Printed in ASA (or ABS) for the best fit and UV/temperature resistance. ... The inner diameter of...

[NT7S](https://www.thingiverse.com/nt7s) had created a very nice cable comb. However it was designed only with a screw mount in mind. ... Since I have a peg board at my electronics workbench, I naturally wanted to have that thing on my pegboard instead...

Ethernet Cable Wire Comb for RJ45 Connector by MineralMike May 05, 2023 I had trouble printing it perfect on SLA. But now it comes out like it should. ... Again NOT my design so all credits go to MineralMike...

Unfortunately I made the error of getting some CAT8 cables which just did not play nicely with other combs I have tried as they are slightly thicker. If I scaled them up my other cables would fall out.So after playing in TinkerCAD I managed to come...

So, I designed a strap and a cable comb with channels for Ethernet, HDMI, and the Roku power cord. The strap is meant to hold the Roku on the wall upside down. On these models of Roku, there's a reset button on the bottom, and if I need to press it...

Designed for Seasonic's 12VHPWR to 2 PCIe cables, has a side clip to hold the two signal cables. This will noticeably make the cable much harder to bend, please use it with caution. This may apply additional force to the 12VHPWR connector. ...Make sure...

A Keystone-type socket is designed for use with Cat5 and Cat6 cabling.

Get Your Cables Organized in No Time with This Handy Clip! Designed Specifically for Those Frustrating 3.4 MM Cords, Say Goodbye to Tangles and Knots! Want More? ...Check Out My Other Innovative Designs Today!

... unit's 16-pin port. ...To make matters worse, my nylon braided cables are too bulky for the main object, so I need to swap them out. ...The piece is stubborn enough that I'll have to carefully carve a small notch in it to fit snugly inside the case.

CAT5 Jack Socket (Rojo)

CAT5 Jack Socket (Azul)

This sleek mount makes it easy to attach a single RJ45 CAT5/6 cable breakout board. Simply pull off the cable chain and snap this on to the hot end carriage right away. ...No more messy wires to deal with!

A blue CAT5 jack port is a networking component used for connecting Ethernet cables, providing high-speed data transfer and reliable connectivity. ...The color blue identifies it as a specific type of CAT5 jack socket, which offers the same...

... item. ...This particular socket, colored in red, is designed to accommodate and securely connect CAT5 network cables for efficient data transmission. ...It's a must-have for any networking setup that demands stable connections and reliable performance.

Cables stay neatly organized with these spacers. ...They keep single sleeve cables tidy, originating from the power source, providing efficient airflow and easy access to internal components.

Tightening up your simple spacers will keep your cable management looking neat and organized! ...This specific type of spacer is perfect for securing single sleeve cable harnesses that originate directly from the power supply unit.

Cable management just got a whole lot neater thanks to these simple yet effective spacers. ...They're perfect for keeping your single sleeve cable harnesses, like those from your video card, well-organized and tightly wrapped.

You'll want to keep your cabling organized, and these spacers help achieve that neatness. ...They're specifically designed for use on single sleeve cables connecting to the graphics card.

Comb

comb

The innovative 3D model showcases an RJ45 CAT5 mounted receptacle, highlighting its design and features in detail.

Cat5 Mount: Self-Tapping Screw Compatible, 2.5 Hole Design This visual guide, represented in a JPEG image, clearly illustrates the type of Cat5 connector intended for use with self-tapping screws. ...To effectively utilize this mount, we suggest...

Create Your Own Parts List: Cable_Comb_2pin_1x2_SECTION.stl Cable_Comb_2pin_1x2_ENDCAP.stl Cable_Comb_1pin_1x1_SECTION.stl Cable_Comb_1pin_1x1_INSIDE.stl Cable_Comb_1pin_1x1_ENDCAP.stl Cable_Comb_1pin_1x1_CLIP.stl Cable_Comb_1pin_1x1_CLAW.stl...

surface mount pc cable comb for 40pin 4mm braded cable

This design features a bottom hole on the first plate of cat5e, no holes on the fifth and fourth plates, no additional plates, a plate size of 0, and a single plate width of 1. The second plate has no bottom hole, while the third plate is also void...