cassette case 3d models

In case you're not using PrusaSlicer, you can print with 0.10mm layer height and 100% infill to get the same results. Note: Be careful when removing the Clock Face from the build plate. It is very light and thin and it is easy to accidentally crease...

UNTESTED but should be noticeably “better”, see notes laterChanged the nut slots to hexagonal to more securely capture the nutsSlots instead of captured nuts in the spider (similar to several other remixes), spaced correctly for M4 pitch and 0.28mm...

(Probably more variants in the future, if needed)  Print instructionsRecommended Print SettingsInfill: 15 %Layer height: 0,20 mmSupports: No Optional hardwareFor fixing the gridthis: screw 3x16 SPAX (schraubenking) - will slightly look...

A good  test is if you try it briefly with the cable, but have your hand on the  power switch to turn it off in case the cables are getting hot. We used  two cables to be on the safe side, because in the first test I created a...

update 11/06/22Since I realised that the solution I had to make new parts of the clockwork extruder, namely changing the bolting direction to the x-carriage, was now the same as the clockwork 2 method chosen by Voron Design, it now means that the...

In this latter case, the design has a small rim in the "frame" (the part with the large rectangular hole in the middle), where the bottom part sinks into to just the right depth. The lid (or cover) is printed as a single piece, and it is universal...

just in case the original author decides to take it down for some reason.) https://www.thingiverse.com/thing:3579224The first 7 pieces replace parts in the original, so obviously dont print the originals of those. 8-11 are in addition to everything...

I highly recommend using a silicone sock for you hot-end in all cases.I have printed for three years with the Hero Me made from 100% PLA with no warping or melting because I have always used a silicone sock. ...If you do not have a silicone sock, I...

In that case you need to ensure the gab is closed when gluing the socket onto the ring. When the ring is done and cured you can do a test run to see if the LED strip survived, but it is not required. If there is no visible damage, then you did not...

The first step is to set the units of measurement for your model; in this case, we're using meters. Once you've done that, you can navigate to the "Cube" tool and create a simple cube that will serve as the base shape for our fence post. Next,...

Customized version of http://www.thingiverse.com/thing:46884 with options: perimeter -1000, qr_tolerance 0.001, per_h 10, per_w 3, tag_height 80, hole_r 10, hole_y 0, hole_x 30, case_thickness 1.8, obj 1, tag_width 80, qr_y 0, qr_x 0, corner_radius...

For this case better use one that fits your spool width. If you have a 42 mm wide spool, take 45 mm. To avoid that the spool is clamped between the arms of the frame, every size adds 2 mm on the left and on the right. The 60 mm size actually is 64...

They make sure that the T-Nuts can rotate freely during installation, your part doesn't slip during installation, and your part doesn't rotate or spin after installation in case you use only a single mounting point.The area around a 3.5mm radius...

Q: Looking at the pictures on your webpage, my initial thoughts scream BACKLASH at me but if that does happen, I guess it would just be a case of increasing the Z-Hop distance to compensate. Yes it would seem at first that there would be some...

#**Mirror Installation** **Cover the dashboard with an old towel in case of drips**. Mix and apply JB Weld epoxy to the assembled *Windshield Adapter*. [Glue this to the windshield, using the *Vinyl Template* to align it...

Please use the one posted here on Printables.com as part of the series:https://www.printables.com/model/157511-cr6-5015-part-fan-shroud-dual-fangThe standard case and thus fan mount does not fit any longer. Since the 4010 blower is largely...

That should allow high speeds with nice resolution but still prevent the axis from moving by gravity.In the case that this is too low there is more place for up to 60T Gt2 pulleys. Also the 20T pulley could be changed against a 16T...

However, the design is fairly static nowadays anyway.rnrnI'll leave the link below for viewing the model or in the unlikely case Autodesk reverses their policy.rnrnORIGINAL POST:rnrnhttps://a360.co/2pR4sEjrnrnYou can download them in a variety of...

Also it feels quite different to spin and creates a little rattling noise when spinning.In case you want to customize things, please install OpenSCAD on your own computer and follow these instructions to customize your ring.Thanks go out to ixpatch...

Both astromecs will compute astrogation data and each one will store at least 3 hyperspace coordinates to allow immediate retreat in case of emergency. Before flight they were to be permanently connected to ship's systems via their computer sockets...

In the latter case grid lines can be inscribed upon it. I suspect (but have not experimentally verified) that an open base is less susceptible to shrinkage than a solid one. Using an open base also results in a much quicker print time (on FDM...

In my case this is 5 segments high. You can theoretically build the lamp as high as you want because the entire lamp consists of plug-in parts. The lamp is fully printable.&nbsp;<br>It is controlled by an ESP32 controller which was flashed with WLED....

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

Note that because this mode requires disassembly of the printer, you may want to print several successive sizes of bearings in case your printer is slightly out of calibration, just to make sure that one set is “tight” enough for you to “hone” the...

These materials might all work well, you just have to be very cautious about the equal weight of the two cylinders. Using 3d printed PLA, ABS or whatever will probably have too low density and therefore you might not be able to see any difference in...

In some cases (like SUNLU), the LockSpool needs no channels because the manufacturer's own reusable spool is designed to be loose.This design produces spools compatible with these filament coils, and any others for which dimensions can be...

[NOTE: It is best to use a glue that gives you enough working time to slide the pieces after inserting all but the last border part(s), just in case…] &nbsp; *I did not need to glue my board, when I used these v6 pieces. They fit precisely into the...

As always I have left the old ones in case someone is in the middle of using them. I will remove all but finished ones in a while to save clutter. I am sure the Prusaprinter people will be grateful for that!</p> <p>When I have successfully created...

This would be convenient if you have a PD capable power supply, since it would run at 20v. Wires I'm using 26AWG silicone wires for the strips, and 18AWG going to the connector (or wire in my case). You might want to solder the wires higher up on the...

It may be necessary to use theVinyl Template* to also cut whereRiser will be attached to the windshield and JBweld theRiser directly to the glass** Cover the dashboard with an old towel in case of drips. Mix and apply JB Weld epoxy to the...