cassandra dimitrescu model

the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic instead. Ive uploaded a reinforced version of the arm that should work better with heavier controllers.i also opened up the...

This model is intended to be glued together using Gloop! Get your Gloop! here: </strong><a href="https://3dgloop.com/shop"><strong>https://3dgloop.com/shop</strong></a></p><p>Assembly made without using Gloop! may result in the need to prepare for...

6) I don't provide holes in the model for the harness or for the charging connector. These are also variable. I happen to use an RCA jack for my charge connection and I just drilled a hole for the silicone insulated wires to exit. 7) I glue the...

Changelog: Update 2021-03-01: Steve (faultedlogic) made a remix for current A8 models with plastic bearing blocks. Update 4 (2018-06-17): added countersunk hole for chain fence Update 3 (2018-06-11): updated left motor mounts for different type of...

Please check the images to see what it is included in this kit.This set contains: - Cultists of Melmora (12)- Plague Knights (4 + 4)- Fosco – Herald of Melmora- Fallen Saint Mordentus – the Penitent- Blasphemia – Daughter of Decay (Cultist...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

The solution is simple enough: Both parts of the model need to be placed away from the centre point (still properly lined up with one another, obviously), so that the probe can do its thing without the first print getting in the way. So began attempt...

(In the future, I'll model a printable screw-gun interface for people who can't get the part in question.) 4.#6-32 brass nut, 1/4" across (measured face to face), 3/32" thick (optional) McMaster-Carr 95130A120. Fits into a pocket on the gun carriage,...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

This brings the Muscle v2.0 advanced cooling system, originally designed primarily for Longer and Alphawise printers, to many more 3D printer models and users. I am even working on testing a custom X-axis mount plate for Prusa/Wanhao and other I3...

UPDATE 09.08.2022 •changed length for diffusor and mount from 10mm to 100mm •orientation changed for some models •added end cap UPDATE 12.08.2022 •added with diffusor / without diffusor comparison photo and electronics box wiring photo •added...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers).For adjustable friction, I've added a simple bail that attaches to...

Slice your model in your desired software and save your gcode 3. Place the created gcode in the same folder in which you extracted the exe 4. Double click to run the exe 5. Type the number of the option you wish to use, for the towers included in...

The COMPLETE Order of the Labyrinth bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The strong Minocs of the Order of the Labyrinth are the descendants of Tesevros the Wise,...

If you use OpenSCAD, the model could be adjusted further refine the diameter of the internal air channel for your needs. Caution, because small changes in diameter produce big changes in airflow! Print Settings ========== The dimensions of...

Http://www.Thingiverse.Com/Apps/Customizer/Run?Thing_id=507810 Instructions Using the Following Options: Custom_phone_width = 100 custom_bottom_fillet_resolution = 8 printer_tolerance = 0.4 stencil_vertical_position = 50 custom_case_pattern_thickness...

This has taken several months to work out the kinks, but I think I have a good working model now. However, here are a few things to note: Prior to any assembling of any of the parts, I have found it is best to pre-thread all of the screw holes...

Supports are built into the models. The fan shroud should be printed with the blower mouth facing up. Trim off the bands tying the barbell studs together and remove the two pieces that support the shelf at the rear.</p> <p>Some good print settings...

The COMPLETE Svartwood Trolls bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Trolls comes in all size and varieties, and being one of the most ancient people, no one knows...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

The tubes used for processing in the Whirlwind would end up leading Ken Olson to transistors, which led to the transistorized TX-O (the love of many a tech model railroad clubber) and later to Olson founding DEC. Suddenly, the Whirlwind was the...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

To connect this to the second hand holder disc, I bought a plastic tube of 1mm inner diameter from a modeling shop. I pinched one side a bit to make it flatter. This seems to work, but maybe I will have to glue it on the pin. I didn't do so yet...

The Version 1 is based on the original model, but with added material to compesate the extended face on the striker, and the second one is something I made because one of my magazines was giving me trouble, not really stoping when it needed. See what...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

SECOND NOTE: I made some corrections to the actual model after I printed it. I got my first attempt working, though it's not perfect. For example the shaft broke off while putting it together. I tried to make it a bit more robust, don't know if that...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

The Hearst Tower, designed by Norman Foster, perfectly embodied the figure of the king with its massiveness and magnificent exterior.After determining the arrangement of the buildings, the next step was the creation of working models, which were...

*Download new version 1.01 here: https://www.printables.com/model/178925-ender-3-s1-stealth-light-bar-easy-to-print-and-do-mod ( Maintaining on Printables ) Easy to print light bar that uses the built in accessory port for power. This allows for...