case for mini xum 1541 floppy usb adapter 3d models

A simple case for the XUM1541 Board by Faszination C64. There are two versions of the top case. One with an hole for the parallel cable or if You don't plan to use it, one without. ... The screwholes will tight fit M3x12mm screws.

Here is the first version of the official Camelot Case for the 1541U II+ tape adapter v3.4. The case might fit other versions too, but I'm not sure about that. Feel free to print it, but if you want to sell your prints, I encourage you to do so at...

This lock was specifically designed for the Commodore 1541-II floppy disk drive. ...Take special caution as it's not just one version, but rather at least three variations of this lock exist.

Case for SD2IEC Mini (a Commodore 64 1541 Disk Emulator). ... Print upper part without support material (that worked best for me).

This one is for MItsumi Newtronics D500 and similar drives. ...I've made it solid, less prone to break when installing.

Floppy Lock 1541-II

I created these collars specifically to provide a more robust connection between the case components - and it's actually possible to eliminate screws altogether by printing two collars and attaching one to each end.\r\n\r\nSpecial thanks go to Tom,...

The main cartridge unit comes in a sleek injection molded case, while the tape adapter ships without one. Two STL files are provided to create a snap-together (with optional screw holes) case that perfectly matches the original design. Although this...

This is lock for a Commodore 1541-II floppy drive. Check if this version is for you. ... Print standing upright with supports.

A case for the Gotek USB floppy drive emulator. Designed for the BBC Micro but may be compatible with other platforms.Three case variants included: no logo, indented BBC Micro logo, and cutout to hold insert with raised logo (which allows the logo to...

This is the case for the RBSC's side slot adapter module for the Gotek floppy emulator or external floppy drives. The Yamaha network module's case was used as the source of this design, which can be easily replicated. Insert the adapter module into...

Case for the Estlcam USB Adapter.

This is a 5.25 floppy case model with discs and some envelopes just for fun.It has 40% of original size.In fact .. ...it was something I did to a project I am building right now.Something to be placed over a small IBM 5150 case :)An entire IBM 5150...

A Gotek USB Floppy Emulator External Mini Caddy based on the internal one I designed for the ZX Spectrum +3 and Amstrad CPC6128/664 although I use this one on my Amiga 500 (with a drive selector switch).As per the internal caddy the front plate has...

The LEWER software is specifically designed for the Commodore Floppy Disk Drive model 1541-II, ensuring optimal performance and compatibility with this particular device.

The case is only slightly wider than the Gotek circuit board and the back opening provides ample clearance for floppy cables to slide in smoothly. Within the print are caps for the OLED socket, which simply slot into place at the top to secure the...

Modded floppy lock mechanism for 1541-II drives utilizing Chinon components.

This is a case for the Atari ST HxC USB floppy drive emulator from Lotharek. It comes in 2 parts, top and bottom. The bottom (no cord hole) allows you to cut your own cable hole. ...The regular bottom part is for a square type cable grommit that came...

This is a critical case for the innovative Device Side Data FC5025 USB 5.25" Floppy Controller board, expertly crafted by visionary Miana Breed. ...Be extremely cautious when handling this device as its base tends to shift out of the lid with minimal...

Designed for FDM printers with dual extruders (two color print). ... This is a remix of https://www.printables.com/fr/model/205968-amiga-500-mini-a500-mini-miniature-full-size-flopp/files

This is designed to turn that useless floppy disk hole into a more useful and modern front panel I/O (USB + audio), which are ubiquitous in modern cases but not usually found in vintage cases. It is a replacement housing for the commonly available...

Embrace HxCFloppy Emulator's USB version for read-only purposes, particularly for Amigas such as CD32, A500, A2000, and A1200. However, opt for the SD-version if you require write support. ...Don't forget to smile because it has an internal speaker!

... needed. This adapter allows you to mount a 12mm switch for your JiffyDOS kernel in that port, which looks better and eliminates the need to drill holes in your 1541 case. ... The switch I used is the UXCELL A14101000ux0766 DS228 SPST from Amazon.

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 15% Filament: doesn't matter PLA doesn't matter Notes: must disable "don't support bridges" in Prusaslicer for full support under the case. ... ...

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 15% Filament: doesn't matter PLA doesn't matter Notes: must disable "don't support bridges" in Prusaslicer for full support under the case. ... ...

The incredible DDI3 USB floppy emulator with 512KB of RAM, expertly crafted by Zaxon, is now available to enhance the Amstrad CPC 464 computer.

This is a Commodore-inspired enclosure for a 3.5-inch USB floppy disk drive, designed to transport modern C64 enthusiasts like those who own THEC64 to the nostalgic world of classic computer storage. To give them an authentic retro experience. ... It...

after my floppy fell down, I had to make a new base. ...

Front Badge file can be downloaded from the remix source THE 1541 Mini Perifractic I'm not sure what is going on but the badge seems a smidge too big for the recess, the badge may need a slight trim or the file could be reduced a few percent before...

Greaseweazle v4 & F1 Plus Mini Case with space for 3.5" FloppyLoosely based on Commodore A1010 drive with space for a flat LED at the front.2 versions of the base one for a Greaseweazle v4 which also needs the toponlylatch printing to secure the...