cartoon character with handlebar mustache 3d models

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:287025 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=287025 Instructions Using the following options:...

I recommend cutting at 0.5mm to 1.0mm if your spring is too strong.Print two leg pieces, left and right.Assemble the springs into the knees and leg pieces. The side of the spring with the small nub goes into the knee. You will likely need to sand the...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

This time, I just re-used his threaded center section to create a spool designed specifically for use with Maker Box filament samples. These tend to be about 40-50g each, and I measured a typical diameter of about 140mm on the loose filament- I think...

This type of moon is called shepherd moon.Type: Satellite. Orbit: Saturn. Orbital period: 14 h 42 min 42 s. Composition: Icy body, mostly water ice, rubble pile. Density: 0.48 g/cm3. Dimensions: 135.6 km × 79.4 km × 59.4...

It also features a full-size SD card slot in the front in case you're tired of fiddling with the teeny tiny ones. If you find yourself needing to access the motherboard compartment on your Ender 3 Pro more than one time after you buy it, for...

... top onto the back/front. Put the side of the top that was attached to the bed front-facing for the best surface finish.&nbsp;&nbsp;These models were printed on an Anycubic Mega Zero 2.0 with a 0.4 mm nozzle in HATCHBOX PLA filament. ...&nbsp;</p>

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

... this 3D model look INCREDIBLY realistic. Would use Rustoleum Filler Printer with sanding to get rid of layer lines. Then apply metallic paint. Then weather the model using black or brown acrylic paint. Can also use some "rub and buff". ... ENJOY!

At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a model by a cnc machine It is possible to model anyone another model according to...

BOM:-Smart filament sensor BTT upgraded version-2x screw M3x10-7x M3 Heat Inserts Nut Heat (same in original )after print carefuly cut the X&nbsp;&nbsp;UPDATE: config:&nbsp;now add Gcode command for turn ON/OFF by: “SENSOR_ON” or “SENSOR_OFF”config...

Then, you'll want to print a mirrored image of the plain extension back and a normal version of the extension back with limit switch. Make sure to orient these parts in your slicer, as the STL files are straight out of CAD and not on the most...

At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a model by a cnc machine It is possible to model anyone another model according to...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Once you have chosen the size of the drawers, you can print multiple drawers with different sections but you should not adjust the Material_Thickness or the Drawer_Width, Drawer_Height or Drawer_Depth settings for other drawers intended for use...

Customized version of http://www.thingiverse.com/thing:116042 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

It requires the input of control pulses with a frequency of 50 Hz, when the duty cycle of these pulses changes, the full power mode is switched to the half power mode. You can read more about this at the link below. I used a control board similar...

And the big curved tiles you can get makes the footprint quite big so i came up with this solution, a smaller curved tile. ... For some reason i can't upload a .pdf today so instead you get the Overview.docx ________________________ <b>If you like...

I found them to be too stiff if printed any thicker than one extrusion width. Very little hardware is required to assemble and all hardware needed is included with your servos! Post-Printing DIY Electronics soldered to a std 50mmx70mm project board...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a model by a cnc machine It is possible to model anyone another model according to...

The choice of TAB key is because it will not trigger any actions, not close any windows, and can only interfere with open text editors.&nbsp;Hardware RequiredThis design needs the following ultra cheap easily available board.Digispark attiny85...

Customized version of http://www.thingiverse.com/thing:287025 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=287025 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

I kept the "arm" in my design (it is the nib that sticks out of the side) but as near as I can tell it has absolutely no function other than to make it easy to quickly line up, during installation, the pin holes on the part with the pins on the...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...