carnosaur aos 3d models

Antenna mount for the AOS 3.5'' frame that fits the TrueRC AXII side feed antenna.

Matek m8q GPS mount and tbs crossfire immortal mount for AOS 5 by Chris Rosser

Aos 3.5 antenna mount with xt30 conector and air unit o3 antenna mount about 4gr

This is a collections of 3D Printed Parts for the AOS CINE35

AOS 35 v1 Runcam Thumb + Nano Camera mount Print in orientation shown. ...Prints without supports.

AOS Falcon 7 GoPro mount for the Hero 5, 6 and 7.

Arm Guards for the AOS 5/5.5 with motor protection. ... Printed from PETG.

Arm Bumper for the AOS 3.5 V2/O3/EVO frame. ... Print in solid TPU.

Mount for Lumenier AXII 2 on AOS 3.5 v2 frame

Print in TPU with 30% gyroid infill. ...Fits AOS 5 and 5.5 V2 / O3 / EVO.

AOS 3.5 v2 Skid 12mm motor close bearing Arm guard, 0.85g weight

Mount for Crossfire Nano RX (Pro) for AOS 5 V5 frame.Use M2 Screws and Nuts.

Arm Bumper for AOS 4/UL5/LR5 1.6mm thick Print in solid TPU.

GoPro 10 and 9 Mount for AOS5, Chris Rosser AOS 5

Mount for the aos falcon 7 adapted to the dji o3 camera

Made for the AOS Falcon 7. Zap strap them to the rear arm braces. ... One on each side, underneath.

AOS 3.5 antenna mount, fits the stock dji O3 antenna and the Radiomaster RP1 ELRS antenna.

Almost a stubby mount for the AOS 5 v2 frame. ...This one fits the Foxeer Lollipop 4+

GoPro asymmetric mount for AOS 5.5" v1. ...Mount shifted to the right so GoPro screw does not touch propellers.

AOS Falcon 7, Insta 360 one r mount. ... Includes a cutout for running the DJI cam wire underneath the mount.

This is a Go Pro compatible mount for AOS Frames with M3 32x32mm moutings. ... Print with >50% infill in TPU.

DJI action 2 perfect fit for the AOS 5 V2. ...Rear backback for a GPS, crossfire antenna and thin Vista antenna

DJI action 2 perfect fit for the AOS 5 V2. ... Rear backback for a GPS, crossfire antenna and thin Vista antenna

AOS 3.5 V5 WS V2 (Dual) Antenna Mount.This is a remix of the AOS 5 WS dual mount from Chillshot.This accommodates the new V2 VTX antennas as well as the AOS 3.5 V5 frame and standoffs. ...I believe this will work on previous versions of the AOS 3.5...

TPU parts for AOS 3.5 -Camera plate protector -Caddx polar nano protector -Arm & motor protector & landing protector -Crossfire Nano & capacitor & Power cable Protector -Caddx vista anthenna protector

This is remix antenna mount for the AOS 3.5 V1 with DJI Vista and ExpressLRS antenna. ... The ELRS works best with the flexible HappyModel ELRS antennas.

This is an example arm guard for the AOS 3.5. Make sure to print two of this part and two of its mirror! ...:D

DJI FPV Cam Mount for Chris Rosser's AOS 5 and 5.5 V2 Frame. ... Uptilt angle adjustable from 25° to 45°.

GoPro / RunCam Thumb Pro mount for the AOS 3.5 Evo frame.Remixed from rlmf's mount, just made it a bit chonkier and added a nut insert.

... mind. ...(0.38g) Also includes a version that has feet to keep the frame off the ground when landing. (0.53g) AOS 3.5 / AOS35 / AOS 35 / AOS3.5 arm guards / landing legs / arm protector TPU 0.2 layers, minimal supports if printing with landing feet