carbon z cub 3d models

horizon hobby carbon cub landing gear wheel skirts. these damn things always pop off. so i thickened the mounting tabs on back and got rid of the ugly slots on the back side. they should fit right on and snap into the oem location. 3 wall no...

This is a new drawing for the Horizon Hobby Carbon Cub. Replacement wheels and tires. My original https://www.thingiverse.com/thing:2872831 worked well for the last 2 1/2 years but it was time for a change. They closely resemble the factory tires...

This is a mount for the Horizon Hobby Carbon Cub S 2 1.3m. I designed it to fit at the edge of my garage rafters which are 24" on center apart. The mount rests on the wing spar next to the aileron servo. The design has 2 holes per bracket to mount...

The original Carbon Cub tires were surprisingly light, but unfortunately lacked any cushion or compression during landings. I decided to upgrade by purchasing the Dubro tires, which weigh in at a substantial 384 grams each. However, I recently...

Replacement motor mount for the 1.3m grey and yellow Cub from Hobbyzone. Save £10 if you're unlucky enough to break yours. Print in PETG or other strong material with 100% fill, as it appears to have been saved at 10% size so enlarge it to 1000%. I...

Prop Adapter Designed Exclusively for UMX Timber and Carbon Cubs

I broke one of these on a bad landing so I thought I'd print them. These are hopefully a little more robust than the factory fairings. ...Please feel free to reach out if you have any issues/suggestions.

was very bored so i decided to speedrun making this cool plane, yes it is very scuffed

To design a 3d printable rc plane was a challenge I had put to myself. What better choice than my personal favorite bush plane? Neutral point is around 55mm from LE.I'm using a Sunnysky x2216 1200kv motor (mounting holes 16x19), 8x6 prop, 1300 3S,...

A battery tray to securely hold the stock battery (Spektrum S3 2200mAh) in the battery compartment of the Carbon Cub S2 1.3m RC airplane.

Replacement pants for the Horizon Hobby Carbon Cub S2 1.3 RC airplane. ... The originals are easily damaged and frequently come off.</p>

A battery tray to securely hold the stock battery (Spektrum S3 2200mAh) in the battery compartment of the Carbon Cub S2 1.3m RC airplane.

My Carbon Cub has 6.5" bush wheels so the modified tail wheel assy. ...I have designed has 2 3/4"

Print on its side with supports Designed around am FMS 1400 Cub's 58mm wheel, a perfect size for a 15cc Carbon Cub bush style tail wheel! ... 4mm carbon rod for the axle and a 3mm metal rod (drill bit cut down in my case) for the upright into the...

Aero sprint/ strut covers for the hanger 9 carbon cub. Printed as per attached orientation. 2x m3x8 or 12 screws to secure the clamp to the 5mm end of the strut assembly. The cover then slides over and is glued to the clamp using e6000. ...(very...

This is an alternative part for the Carbon Cub S +, R/C aircraft from HobbyZone. After my plane crashed, I had to replace its damaged nose and designed a new piece myself. This version has a more aggressive appearance than the original part:) The...

cub

Customized version of https://www.thingiverse.com/thing:4445719 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4445719

The stock landing gear skirts are very fragile and one rough landing and the tabs will break off. ... These are direct replacements for the stock design, but use small zip ties to attached the skirts to the landing gear assembly and will never fall off.

I broke the battery stop on my Morgan Mill RC Carbon Z Cub battery holder so 3D print to the rescue. ... http://www.morganmill.com/RC/Carbon_Z_Cub_Parts.html

The battery holder is designed specifically for the Horizon Carbon Z-Cub RC aircraft model, ensuring proper fit and function. ...

This accessory holder is specifically designed for the Cessna 150 Carbon Z from Eflite. Its primary function is to securely store two crucial components: wing screws and antennas. ...To ensure optimal performance, it's intended to be carefully attached...

E-flite Carbon Z Trojan T28 Flight System Upgrade with Enhanced PLA.\nPrint Settings\nPrinter:\n Da Vinci 1.0 Pro\n \n Rafts:\n No\n \n Supports:\n Yes\n \n Resolution:\n 0.2mm\n \n Infill:\n Solid

This is a mount to attach the wing strut to the wing on the E-Flite Carbon Z Cessna 150. Anyone with these airplanes probably knows how brittle some of the plastic parts can be and if you aren't careful you'll end up breaking the mount. This part...

I wasn't quite satisfied with the design of any CR-10 Z-braces I'd seen, and I had some carbon fiber tubes left over from other projects, so I decided to model some little mounting brackets in Blender and put them to use. You will need: M5 tap, to...

This is a printable spinner based on the UMX spinner (EFLU5609) & (EFLU3958) from Horizon Hobby for the 5 x 2.75 propeller (EFLUP050275), which is used in the following planes: UMX Cessna 182, UMX Carbon cub SS, AS3X beast, Sbach 342, the original...

This is a printable spinner based on the UMX 2-blade brushless spinners (EFLU5609) & (EFLU3958) from Horizon Hobby for the 5 x 2.75 propeller (EFLUP050275), which is used in the following UMX planes: Timber (the original 2-blade), Cessna 182, Carbon...

This is a mounting tray designed specifically to take the place of the standard GPS unit. ...It is engineered to securely hold a 30x30 Flight Controller, GPS module, and receiver in one convenient package.

This is a highly advanced, operational elevator tail gear system.

Rudder for carbon z cessna conversion to early model taildragger