captain rex action figure 3d models

It's up to you to figure out how you want to accomplish this. Wall Mount There's already a wall mount for this model on Thingiverse, but it's pain to print so I made a new one and included it here. It prints in two pieces, without supports, and...

you can run it with out a top and it works just fine just try to avoid looking into the pretty pretty lights for long with out proper protection.--- If requested I can make a little lid for this----, It just wast something I personally saw the need...

 3/6/2023 - Added v9.3 for Dragon C, thickened frills. I also decided to figure out a better way to manage all these models. The purpose of this listing was to make the Spirit Dragon, the best it could be.  I think I got there with v8.3.  But every...

If you can figure out where to put 2 3mm (1/8") holes that are 26mm apart on center vertically, then you might be able to just mount the flat mount directly to the fan cover. It is very light weight. I printed and am using my second to final...

(LOL) Trust me, you'll figure this out quick. It was my idea, and I still had to mess around with each screw for a few minutes. Again, printing the included hopper body will make your life WAY easier. 7. Fully install the auger by screwing the...

There's an optimum ratio which you can figure out by testing them. Too much petroleum jelly, and they won't catch a spark, too little, and they either can get wet, or they burn too quick. The right ratio should yield a water resistant tinder, with a...

Since I have been experimenting a bit with creating homemade springs using generic music wire, I figure this is as good a place as any to document the implications and insights I've run across in this particular process. So skip the following...

Seeking for a nice weekend project I stumbled upon this belt: https://www.thingiverse.com/thing:325458 When I saw this I figured wouldn't it be nice to have a belt which comes off the printer fully assembled? It took more than a weekend but here we...

I was fortunate to figure out I could trick the firmware and say the physical max endstop connections were the min. Everything worked out until I blew the Z axis endstop (no idea how that happened). I had to replace that board. Went dual extrusion...

Previous designs I've posted have been converted from models available elsewhere on the internet, where I’ve converted them and figured out how to generate meshes suitable for printing. I was looking for a project to learn more about creating my own...

This offers three advantages over the original design: The user can access any level of the body by removing a maximum of 4 M3 screws. Creates hard point mounts for future mods and/or add-ons Removes and replaces the standoffs that where used to...

Toppo shows a humble side when he admits that he is not the strongest in Universe 11 and that his close friend Jiren holds that title, while he is the second most powerful one.ABOUT THIS 3D FIGURINEThe model is saved in STL files, a format supported...

Stay tuned ... ### Questions (so far): 1) I tried to figure out a "good size". The board should be both visible and at the same time not take up too much space. I.e. a person should find space on his/her desk. This idea clashes with the principle...

He was married twice and loved fast cars, fine food, bad jokes, and was an engaging and enigmatic figure. He studied measure theory and broke dimension theory into algebraic operators. He studied topological groups, operator algebra, spectral...

For my application, since I will be using ‘half-clips’ (see attached photos), I did not worry about figuring out how to use full toe clips with straps. There are possible solutions, but these would require additional modifications to the pedals. FYI,...

I have decided to upload each individual group of figures by position in their own zip file to make it easier (small file size) for you to download. As per my usual, each Zip file will contain the model un-based, based, and with supports. ...

 Filament doesn't melt when it touches the protoboard strips.Attach the power wires to a variable voltage power supply (I use a DROK 120V to 0-36V supply, but there are many fine options), and set the voltage to whatever will get around 10 watts...

Pretty easy to figure out where these go :D Because edges don't always print flat, i sanded the edges that will be glued together to ensure a flatter surface for adhesion. Glue the 2 pins into the Support Bottom. Using the square pin, glue the...

Unfortunately I am having trouble figuring out how to fit the "... Player card 2.x" versions of the player card into the box with the new card holders. Currently only the "... Player card 1.x" seem to fit nicely in between.</p> </blockquote>...

Figure out which way your servo swings and choose accordingly . Version A is offset a bit CCW, whereas version B sits CW. Choose which one is closest to minimize any center adjustment you may need to make later in your flight controller.Also included...

The god created Adam as figure and he was 60 arm length , both elves including Satan and angels were scared of this new form because they never seen any thing like him before , but Satan feeled jealous and begun kicking him and go through his body to...

😄 м assistant Project: The Anatomy of a 3D Printer Explore the Y and X axes in action Show your appreciation by hitting the '♥' button when downloading my model. Your support is what fuels creativity, so keep on printing with enthusiasm! 😉</s>...

ABOUT THIS 3D FIGURINEThe world of the Hollow Knight action-adventure game is riddled with ancient mysteries, and everyone living there seems to have a secret of their own. However, there's always a brave soul who dares challenge the monsters...

Anyway, I consider necessary using metallic shafts for each of the two front "shocking tubes", the same as a pair of 10x32mm more common springs which really makes the front shocking action. I created some "TPU seals" for the front fork shocks so you...

**Required Items:** https://bit.ly/3qQvf2r **Recommended Actions:** 1."DDW_RN-3DP27_Filament_Holder_50-55mm.stl" needs Density 5%, Wall Thickness 1.2mm, Top/Bottom Thickness 1.2mm. 2."DDW_RN-3DP34_X_Cable_Carrier_4.stl" is the only cable carrier...

10 January 2019 : Added "Half Buse V1.1 for the people who want to see the printing head in action or using a BLTouch like this onehttp://s.click.aliexpress.com/e/MizWXDX6 Beware the fact the cooling maybe less efficient with this optionparts are...

The author of the K9 Mark I for 3D printing also couldn’t resist the robot’s charms given its encyclopaedic knowledge and vast computer intelligence and spent 30 hours in total to design the action model of the well-liked K9 mechanic dog. A lot of K9...

update 5: what next now that it is finished ?(Sunday 1st Nov 2015 Australia) update 6: Its fits in the back of my little car (so if it fits in a MINI then it fits in most cars(photo added to gallery) update 7: We have a very short youtube video here...

The Jurassic Park franchise contributes to this fantasy through spectacular action and the portrayal of dinosaurs in such dangerous yet exciting proximity to humans.Blue & Baby Blue 3D Printing Figurines in Diorama are a beautiful tribute to the...

Name: Light_Bridge_Leader\nVersion: Alpha_11\nPreview: Enabled_by_Default\nUnits: Metric_Measures\nDimension: Five_Foot_Nine_inches_by_Eighteen_Inches_by_Three_Hundred_SevenpointSixFive\nGeometric_Parts:...