cap and tassel 3d models

A container with a fastening top, featuring a 36 millimeter-sized bottle and a securely screwing closure.

3D model including the top and bottom end allowing the closing of the shutter on a Ø14mm polycarbonate rod.

Check out this epic YouTube video at https://www.youtube.com/watch?v=dFhspXtGMX8 and experience its electrifying impact for yourself.

I designed this specifically for the sanitized bottles and lids. ...The printer will use a bed-support feature to accommodate the openings.

Model rockets soar to incredible heights on a single burst of fuel, leaving a trail of smoke and fascination in their wake.

I edit and remesh different types and models of roblox avatars. If there is one which is looking close to your roblox avatar, you can 3D print it. Most of the avatars uploded by me, I already 3D printed it as you can see on my TikTok account. ...You can...

Great little gadget to use to open the pull tab on your soft drink or beer can, a quick turn and the can is sealed up from bugs etc, . Printed with PLA, standard Prusa .20 settings, supports on build plate only. ...Fits 355ml cans and may work on others...

... you can and 100% Infill. ...Each part should work with the original Counterpart. You have to glue the magnet in and maybe soften the plastic a bit by heating it up. ... If you need a base try this one: https://www.thingiverse.com/thing:4259926

I create Toxodenta shapes from Occlupanidae at a 600% scale for each of my filaments, giving me a substantial piece to display and examine as an example. Instead of leaving them scattered around or stored in a box, I designed this stand and extender...

I redesigned the dab tool so it can twist and lock so it can stay closed in your pocket. I also made a shorter version (V11) so it can fit in an altoids tin box. ... Enjoy!

I'm designing a straightforward project for the Arduino Nano. ...This marks my initial experiment with Tinkercad, and I'm excited to share it with you. ...The model was printed using high-quality PLA.

Versions three and four are tailored to fit snugly over a 5/8-inch hole and a 7/32-inch (approximately) thick plastic gasoline can wall. Version five, on the other hand, is optimized for a 1/2-inch hole and a 1/16-inch (approximately) thin plastic...

... is a rewritten version of the original text. ... Covers are available for both MPX and XT60 battery types. ...A new, vibrant green color indicates a fully charged state, while a stark black background signals an empty battery level, labeled as "Tom".

The simple Apple pencil case safeguards the stylus and clip from damage. The case functions exceptionally when printed with Ninja Flex, while the clip performs admirably when printed with ABS plastic. ...To ensure a precise fit, print at 101.5% scale or...

... a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. ... It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the back-center. ... A M3-.50 nut is required.

The kit comes with snugly fitting ends and rings designed to accommodate 3mm filament in larger holes or secure it outside smaller ones without requiring much cleanup. Among the tapered ring, the best option for holding is available. Although these...

... My solution: I pull out the electronics from the sticks, toss the case and print a new one. A little hot glue helps keep the internal board from shifting around. ... Of course, you can choose your own color - I went with a fruity mango-orange.

... resistor</strong></p> <div><p>To dim the led simply change the resistor</p> Original value is 67 Ohm. ...Change it to 120 or even 220 Ohm to match the original bulb yellowish light add the diffuser print it and push it on top the leds Category: DIY

This is a quick print hitch pin sleeve and Kuat specific lock cap when attached, helps to minimize metal to metal impact on the hitch. This helps to save the powder coat on the hitch from flaking off.Printed with 0.4mm nozzle, 0.2mm layer height, 5...

TASSEL 1 SCONCE by Apparatus 3d model

Roman Curtains 60 | Next | Tassel Edge

oman Curtains 07 | Tassel Edge | Harrow

General information:

Here is a rewritten version of the original text: Handcrafted 4-inch Decorative Fringe Creator

A blind cord condenser. ...Screw part need support (I suggest regular support, not tree).

Here's what we've got in stock instead.

... standard pco 1820 bottle cap and neck. ... Check out this similar design, the Bottle Cap and Neck PCO 1881: https://www.thingiverse.com/thing:2203127 Or try another version, the Bottle Cap and Neck - PCF-38P-5: https://www.thingiverse.com/thing:2795244

Cap that fits on the end so BBs don't spill out, and a new piston that has a holder for said cap.

Simple toothbrush cup with tilted bottom, draining hole and a cap suitable for three toothbrushes