canyon speedmax computer mount 3d models

You can order it from Shapeways at https://www.shapeways.com/product/5JBJU3MJD/bike-headset-stem-computer-mount (I don't get any money from this!). I've only printed it on an SLA printer, but I don't see any reason why it shouldn't print absolutely...

An other mount for my Sigma Rox 11 (Garmin Base). ...This time for the **Canyon G5 Stem**. You need two **M3 countersunk screws**... i used my dermel to shorten them. Design is basd on an other mount from **Lars Vogelenzang** but build from scratch.

Size specific Go Pro mount for the Canyon S27 seat post. The mount design contain 2 pices, that bold on the seat post. ... Required Hardware 2 - M3 (3 mm) x 14 mm socket head cap screws 2 - M3 (3 mm) nylon insert lock nuts 1 - M5 (5mm) x 22 mm 1 - M5...

This is a fan mount for a 140mm computer fan. It allows the fan to stand upright with 2 screw hole points, and an offset base to account for the fan weight offset, plus the force from the direction of air (fan should blow towards the smaller side of...

A sturdy attachment for the Suaoki bike wireless computer is needed, and I have access to one without cadence function. However, it's likely that the mount will be identical in design to the one with cadence capabilities. My primary concern is the...

A person required a computer to facilitate three-dimensional scanning.

A small, lightweight spoke mount for a bicycle computer magnet. You need two short M3 bolts and preferably an M3 tap (you could also use the M3 bolts to create the threads, but this is not the preferred method). No support material required. ...It...

A small, lightweight spoke mount for a bicycle computer magnet. You need two short M3 bolts and preferably an M3 tap (you could also use the M3 bolts to create the threads, but this is not the preferred method).</p><p>No support material...

A small, lightweight spoke mount for a bicycle computer magnet. You need two short M3 bolts and preferably an M3 tap (you could also use the M3 bolts to create the threads, but this is not the preferred method). No support material required. ...

A small, lightweight spoke mount for a bicycle computer magnet. You need two short M3 bolts and preferably an M3 tap (you could also use the M3 bolts to create the threads, but this is not the preferred method). No support material required. ...

This is a 3D Printed Garmin mount suitable for all the Edge models including 200, 500, 510,520, 800, 810,820, 1000 and 10300 models and designed to work with the Canyon Garmin Mount for H31 Ergocockpit. The mount also has a holes underneath to hold...

... designed to respect the Aero form. This mount is made for the Canyon H31 Ergocockpit, but i can be easily addapted to other handlebars. ... Fits CanyonH31 Ergocockpit and newer models and other integrated handlebars with two underside mounted bolts.

The round adapter piece fits over the arm of the clamp, and mine stays firmly in place as a result of the zip ties used to attach the computer mount base to the aerobar mount/adapter. It could also be glued or a small screw could be used, if...

Simple, universal, bungee-style wrist strap designed specifically for bottom-timer devices or computers. ...Compatible with computers featuring a width of 55mm and a depth of 24mm.

this mount attaches to a standard garmin bike mount for their line of bike computers like the 800, 810 and 1000. Replace the two screws that come with the bike mount with 10mm hex screws. Make sure you use some locktite to make sure they don't come...

I may or may not come back to improve on these flaws, but you are welcome to print and try it out.Most computer cases have a mounting for a fan at the bottom of the case. However, for my case, that was unusable after I changed to a longer power...

I may or may not come back to improve on these flaws, but you are welcome to print and try it out.Most computer cases have a mounting for a fan at the bottom of the case. However, for my case, that was unusable after I changed to a longer power...

I have set the majority of printed parts in a way to strengthen the mount.Mounting Hardware Required:4x M4x10 Cap Screws4x #10x1-½ Countersunk Screw (recommend using wall anchors for drywall)Order of Operations of text files converted back into...

... extra support. ... for this you have to print this part two times. Ich hab den " Tablet/Computer underdesk moun" von "OSXtraveller aufgeteilt zu einem, damit man es ohne extra stützen drucken kann. ... dafür muss man eben dieses teil 2x drucken.

This one is like the canyon mount and the wahoo roam mount had a baby… I made it so it has a twist mount that can be printed separately and then bolted in. so if it breaks it can be replaced easily. The twist mount was modeled after the K-Edge...

Designed these bad boys to hold up my computer - and they work. They are big for rigidity, not for strength. Requires 8xM5x25mm + 8xM5 Washers for the entire setup (4 each bracket). I tap the holes first but you don't have to - depending on the...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: No Supports: Yes Resolution: .2mm or greater Infill: 20% How I Designed This Open Scad I designed this network switch mount in OpenScad, incorporating the internal L,W,H...

This mount works in the dashboard and tray contours of the 2015-2022 Chevy Colorado and GMC Canyon. Use a good double-sided tape on the back of the mount in the tray area and in the front of the mount on the stereo fascia - you need to stick...

This mount conforms to the dashboard and tray contours of the 2015 and above Chevy Colorado and GMC Canyon. There's room for double-sided tape on the back of the mount in the tray area and in the front of the mount on the stereo fascia - no need to...

This is a wahoo cycling computer mount that is compatible with Giant computer mounts

Hubby loved this print but wished it had a mount for his light too. ...I added screw-holes for the GoPro style mount allowing him to attach the mount he already had. Note this is JUST for the plate itself. ...The GoPro style mount he purchased.

... i used my dermel to shorten them. Design is basd on an other mount fromLars Vogelenzang but build from scratch. ...Print Settings Printer Brand: Creality Printer: Ender 3 Supports: Yes Resolution: 0,2 Infill: 25% Category: Sport & Outdoors

Printed in prusament ASA.I used the upper part of the stock mount which is screwed on the printed part.Stock mount is this reference...

... Prints in less than 2.5 hours. Update: adding a version of the STL which has a mount adapter for a Moon Comet right underneath. A nice daytime flash if you have one. Probably fits some other lights too. Remixed from another Moon adapter. ...

Printed in prusament ASA.I used the upper part of the stock mount which is screwed on the printed part.Stock mount is this reference...