canon to nikon lens adapter 3d models

This is a unique blend of two adapter designs, drawing inspiration from the following sources: http://www.thingiverse.com/thing:1727361 http://www.thingiverse.com/thing:237376 While I'm credited with bringing these adapters together, their original...

... at an angle, rather than flat. Additionally, printing two copies of the "clip" part will provide extra secure fastening. Please exercise caution when using this adapter to avoid any potential damage to your Canon EF lens or Nikon 1 camera body.

Scale Z of the '4mm spacer' file to 4.2mm for Canon or 5.7mm for Nikon in your slicer, then print. Epoxy the 1/4" 20 nut to the camera adapter. Remove the lens mount from the extension tube set. Glue the extension tube to the spacer. Glue the spacer...

First published recently, this adapter allows Canon EF lenses to be mounted on an old Nikon lab microscope. Based on the maker's earlier EF Mount design, it can be printed without glue or heat. While it is a mechanical adapter with no optics, focus...

Adapter for using Nikon F lenses on Canon EF-M cameras.

I tried several iterations of a fully 3d printed adapter but the Nikon mount is quite thin so I settled on 3d printing the GFX side and then epoxying a Canon EOS to Nikon F mount adapter to the front of this after sanding the gfx side down to exact...

Hello, today I made this Canon FD Adapter for my Nikon Z Camera, because I recently got my hands on a Canon FD 300mm F/4 for a bargain online. I am not an expert in 3D Modeling, but I made this using Blender. Cura shows "Errors" in the print...

Obviously only in manual mode.The 1x adapters flange focal distance is the nominal 46.5 mm for Nikon F mount so the lens can still focus on infinity. PrintingThe model should be printed with 0.4mm nozzle and 0.2mm layer height.The model is split into...

 When sandwiched between two objects (camera lens and eyepiece mount), the delicate plastic threads of this adapter are largely stressed only axially with the force of the thread torque, from front to back of the lens system. ... If any gap is left...

Adapter for Zwo Asi 120 Camera Mounts Allows Installation of Nikon Lenses Unfortunately, I've discovered that this version makes it impossible to infinity focus. ...A corrected version is coming soon.

... be used as is for taking photographs. To overcome this limitation, a custom-built photographing system featuring bellows was created. Given that the enlarger lenses use the L39 mount, I designed and built a converter to adapt them to Nikon-F mount.

Nikon FT1 Adapter for Nikon 1 to mount to F lenses. ... not tested yet, but it should work

Nikon FT1 Adapter for Nikon 1 to mount to F lenses. ... not tested yet, but it should work

EF-M to EF Canon Lens Adapter Mounts Securely onto Tripod for Steady Photography Sessions Always Ensure That the Integrated Tripod Support is Properly Positioned on the Right Side.

I share with you my design to adapt Altix lenses like the famous Trioplan to Canon R mount mirrorless cameras (R, R5, R6, R3, RP, Ra). The design has been perfectly matched with a Canon EOS R camera testing that it focuses correctly from its minimum...

... firmly, preventing any movement. To align the adapter perfectly, simply line up the red dot on the lens with the small dot on the mount and turn it clockwise until it clicks into position. ... 1 x 25mm M3 screw A small spring from a ballpoint pen

... 40.5mm diameter. This is an adapter to Canon EF mount for those 40.5mm lenses, the thread has been designed a little larger to facilitate printing via FDM whilst still providing a tight fit. ...The design may allow for focus slightly over infinity.

I share with you my design to adapt Canon EOS mount EF lenses (5D 6D 1200D 700D 750D 800D 70D 77D 80D...) to mirrorless Sony E-mount cameras (A7 A7II A7III A7RIV A5000 A6000 A6300 NEX-3...) The design has been perfectly adapted with a Sony A7II...

Line the red dot on the lens with the small dot on the mount and turn to the larger dot until it locks. 1x 25mm M3 screw and nut Half a spring from a pen. ...Empiricus@Dremomys Print Settings Printer Brand: Monoprice Printer: Maker UltimateRafts: No...

Adapter for mounting Pentax 6x7 lenses on Canon EF-mount DSLRs. Securely fasten the camera and lens in place by aligning the red dot on the lens with the small dot on the mount, then turn until it clicks into position. ... 1 x 25mm M3 screw A spring...

The adapter seamlessly connects Nikon F lenses to Canon EF cameras, its substantial design making it an ideal candidate for use with a lens tube. ...Printing settings are as follows: Printer: Monoprice Select Mini Rafts: Yes Supports: No Resolution:...

Desinged for 2 configurations: Canon EF LENS 50mm 1:1.8 STM Canon ZOOM LENS EF-S 18-55mm 1:3.5-5.6 IS STM But with the parametric design it's easy to add new configurations (either do it yourself in solidworks) or ask me in the comments to add a...

Line the red dot on the lens with the small dot on the mount and turn to the larger dot until it locks. 1x 25mm M3 screw and nut Half a spring from a pen. Empiricus@Dremomys Print Settings Printer Brand: Monoprice Printer: Maker UltimateRafts: No...

To optimize its performance, simply attach your wide-angle lens (18-55) with a 58mm diameter to the adapter's second section. With this setup, you'll be able to capture exceptional macro images. ...It's essential to note that printing it with multiple...

This is a versatile converter designed specifically for attaching MC mount lenses to EF mount capable Canon digital cameras while retaining compatibility with analog Minolta cameras.

... etc. ...but it works as it is though it clamps to the rear of a BNCR lens with a number of screws rather than twisting a bayonet mount.. So it's not suitable for quick lens changes, unless you have one on each lens! ...Requires 8x M2.5x12mm screws

... no longer use my Minolta Maxxum 7000 because it's a film camera. ... If you are like me and have a substantial investment in AF lenses that you want to put back into service for your newer Canon that uses EF lenses, this is an awesome and useful print.

I have created this mirror in the shape of a lens, the mirror to be placed must have a diameter of 25cm. Any suggestions or any information, you can contact me on my profile mail. I can modify it for any lens of any brand. ... I hope you like it!!!

The flange focal distance of the Nikon F-mount won't allow you to focus to infinity even if the EF-lens is fitted directly to the camera. An additional conversion ring will make it even worse. So, why design and print it? I had to equip a high-speed...

The camera ring adapter seamlessly connects Canon lenses to the Nikon AF-S NIKKOR 24-120mm lens, allowing photographers to unlock a vast array of creative possibilities with their existing gear.