canon 100 to 400mm lens 3d models

It is a snug fit on my lens, I suggest you cancel a test print to make sure your fits on your lens printing on your printer. Scale slightly as needed. I've been printing out of ABS since it will be out in the sun, and in my car on the road trip out...

There are three body options available: * Main-body (no hood) * Main-body-w-hood (with standard hood) * Main-body-w-hood-thinned (with thinned, narrower hood for reduced plastic usage) Optional parts include: * Rear cap (covers the lens side of the...

Canon 400mm f5.6 lens with a quick mount bracket from Benro attached to the lens collar.

Materials needed: 2X M3x12(or 14) screw 6X M3x8(6 might work) flat head screw (flat head not required, just looks better) This design allows you to align your film onto a holding ring and then install that ring inside the lens hood. I highly...

I designed this so you're able to align your film onto a holding ring, and then install that ring inside the lens hood. I highly recommend you TEST this out on something cheap and similar to your solar film. If using the Baader film I'd recommend...

I used ABS but I think PETG would work as well.I will look into designed a front cover for this in the coming weeks.Materials needed:2X M3x12(or 14) screw.6X M3x8(6 might work) flat head screw (flat head not required, just looks better).I designed...

Bahtinov Mask for Canon EF 100-400mm on ET-83C

Canon EF 100 Lens Holder Perfect way to store your camera gear if you don't have them in your bag For table or for wall mount Lensholder Canon EF100 For wallmount, use a nailplate 60x60x40x2,5mm

I modified the mask to accommodate the Panasonic-Leica 100-400mm zoom lens. I also made an adjustment to enlarge the fit of the mask, and added small felt pads inside the three prongs to provide a better grip on the lens hood without scratching it.

Replacement lens hood for the Lumix (MFT) system Panasonic-Leica 100-400mm zoom lens. Replacement is the same size as the original, and mounts the same way (normal or reversed to stow), except that the clamp has been redesigned to allow for single...

2 versions: 1. just a hood 2. ...a hood with a godox MFAR ring

Focuser for Canon 100-400 mm Lens and Other Large Diameter Lenses for Astrophotography Camera Use. The inner diameter of the lens clamp is precisely measured at 93.7 mm. To print this focuser, use a high-quality PETG or ABS filament with a solid...

Engineer carefully installs a versatile connector to secure two lenses side by side.

Adapting Canon Lens EF 400mm 1:5.6 L (Ultrasonic) for Astronomy with ZWO EAD EAF holder is compatible for [SCT](https://www.thingiverse.com/thing:3992198), [Newton](https://www.thingiverse.com/thing:3992200) or...

Adapting Canon Lens EF 400mm 1:5.6 L (Ultrasonic) for Astronomy with ZWO EADEAF holder is compatible for SCT, Newton or Refractro telescope.Fine manual focus available too.OpenSCAD source code on GitHubBOM1x Canon Lens EF 400mm 1:5.6 L (Ultrasonic1x...

It's a highly detailed, low-poly 3D model of Canon EF 400mm f/2.8L IS II USM Super Telephoto Lens used in various fields like game development, advertising, interior design, motion picture art, and visualization. This model was created from...

Canon RF 100-500mm Lens Hood Rubber Protect Ring This can protect the lens hood when using it to stand.

A very simple solar filter design and storage case for the Tamron 100-400mm f4.5-6.3 Di VC UUSD lens fitted with it's lens hood

EF-M to EF Canon Lens Adapter Mounts Securely onto Tripod for Steady Photography Sessions Always Ensure That the Integrated Tripod Support is Properly Positioned on the Right Side.

I share with you my design to adapt Altix lenses like the famous Trioplan to Canon R mount mirrorless cameras (R, R5, R6, R3, RP, Ra). The design has been perfectly matched with a Canon EOS R camera testing that it focuses correctly from its minimum...

... firmly, preventing any movement. To align the adapter perfectly, simply line up the red dot on the lens with the small dot on the mount and turn it clockwise until it clicks into position. ... 1 x 25mm M3 screw A small spring from a ballpoint pen

... 40.5mm diameter. This is an adapter to Canon EF mount for those 40.5mm lenses, the thread has been designed a little larger to facilitate printing via FDM whilst still providing a tight fit. ...The design may allow for focus slightly over infinity.

Desinged for 2 configurations: Canon EF LENS 50mm 1:1.8 STM Canon ZOOM LENS EF-S 18-55mm 1:3.5-5.6 IS STM But with the parametric design it's easy to add new configurations (either do it yourself in solidworks) or ask me in the comments to add a...

Line the red dot on the lens with the small dot on the mount and turn to the larger dot until it locks. 1x 25mm M3 screw and nut Half a spring from a pen. ...Empiricus@Dremomys Print Settings Printer Brand: Monoprice Printer: Maker UltimateRafts: No...

With a 1.25 "telescope eyepiece", you can transform your EF lens Canon into a powerful spyglass. The view will be upside down, but don't worry about that - the magnification achieved is truly remarkable. Tested on Sigma 28-300mm lenses, which work...

Part for FD to EF lens conversion

I created this lens hood for the Olympus micro four-thirds 100-400mm non-professional lens, which takes an LH-76D hood. If you want to check whether it will fit your lens, the outer diameter of the end of the lens should range between 75-77mm and the...

I share with you my design to adapt Canon EOS mount EF lenses (5D 6D 1200D 700D 750D 800D 70D 77D 80D...) to mirrorless Sony E-mount cameras (A7 A7II A7III A7RIV A5000 A6000 A6300 NEX-3...) The design has been perfectly adapted with a Sony A7II...

... Pentax 6x7 lenses on Canon EF-mount DSLRs. ...Securely fasten the camera and lens in place by aligning the red dot on the lens with the small dot on the mount, then turn until it clicks into position. ... 1 x 25mm M3 screw A spring from a ballpoint pen

This is a adapter to put Canon EF lenses on a RolleiFlex SL66. ... (this is a test part, be carefull with your lenses and camera).