canik mag extensions 3d models
74986 3d models found related to canik mag extensions.
thingiverse
This is a pinky extension for a canik tp9 sc magazine. It does need a bit of sanding to smooth things up but otherwise it works and does its job. I printed it in petg so that in heat it wouldn't melt and is a bit stronger than pla. I used...
prusaprinters
Double mag pouch for Canik TP9 SFX pistols designed to use Safariland ELS mount. ...I believe this will fit all TP9 Magazines</p><p>There is O-Rings between the plastic to hold tension on the retention screws.</p><p>Hardware needed</p><p>(2) M5x20...
thingiverse
Was looking for a stand for my TP9 SFX, but wasn't fan of the ones that had space for 15 rounds of ammo, so I decided to remix it and add 3 mag slot. ... Enjoy
cults3d
Was looking for a stand for my TP9 SFX, but wasn't fan of the ones that had space for 15 rounds of ammo, so I decided to remix it and add 3 mag slot. ... Enjoy
thingiverse
These are magazine base extensions. I used 3m Scotch Extreme Mounting Tape to mount them to the magazine. ...I have never had any trouble with them falling off.
thingiverse
These pinky extensions for Taurus G2C magazines, 9mm and 40 S&W, have yielded optimal results when printed with PETG filament. However, I've encountered significant issues with the 9mm base model, which consistently displays imperfections. Despite...
thingiverse
This my first with 3d printing work for my TP9 Elice SC.
thingiverse
Canik Single and Double stand for the TP9. ..."Double" and "Single" stand does not contain model names and any "machine" that takes TP9 mags should fit.
grabcad
It's recommended to print with supports, rotate the model 15 degrees towards the backside to prevent supports from appearing inside the extension. 80% -100% infill required. ...May work with PLA due to the amount of plastic that I could place around the...
thingiverse
It is recommended to print with supports, rotating the model 15 degrees towards the backside to prevent supports from appearing inside the extension. Eighty to one hundred percent infill is required. PLA may work due to the amount of plastic that can...
thingiverse
This is a gun Holder for the Canik TP9sfx. Note: this was accidentally saved in micrometers. Skillet to 1000% and everything should be fine. ...Currently working on a fix sorry for any inconvenience.
cults3d
Canik Mete Ver 1 Stand with LED Backlight space Options available for: 1911 .45ACP Single Stack Vektor SP1 9mm & SP2 .40 S&W Variants Baretta 92 9MM & .40 S&W Variants
cults3d
I have also design trim jig for this mold https://cults3d.com/en/3d-model/tool/canik-mete-sft-owb-trim-jig https://cults3d.com/en/3d-model/tool/canik-mete-sft-iwb-trim-jig Please fill free to contact me if you need any help with this mold. ... 3D...
thingiverse
Charging handle for Canik Rival. This replaces the single sided charging handle that comes with the Rival. The stock handle is uncomfortable, at best, and largely unuseable. ...This design attaches to both sides of the slide and provides a wide,...
thingiverse
Simple attachment for the Canik TP9 line. Push the rear lug into the accessory slot and slide the magazine well over the front edge of the pistol frame. It clicks securely in place. ...The attachment stays firmly in position but can be quickly removed...
thingiverse
It should work with most any Canik pistol, but I have only tested it with my TP9SC Elite and MC9 Mete with a small generic light attachment. Note: I do not have small children in my house, so having a loaded pistol sitting around is not an issue...
thingiverse
This is a recreation of existing aftermarket magazine baseplates for the Canik Elite Subcompact (Freedom Smith baseplate). I will likely release another for the extended 15 round magazine in the near future. Will add a place to better secure magazine...
thingiverse
Edit it online https://www.tinkercad.com/things/4pUzFg3GMhq First time in cad, so not perfect, fits the rmrcc slide of my canik mete sfx so i can put a much more affordable red dot on Again, this is my first design and time in cad, hole should be...
thingiverse
... down slightly for a snugger fit and added a tapered cut. Printed first version and it still inhibits mag release locking so I refined further (v2) and that should do the trick. ... All that said, with the cut-outs, it might not be buying you much.
thingiverse
This Goes to a Canik METE SFT holster. Made with 3d Fuel pla+ black, I print them on the side no support and at 50 mm/s on the ender 3 pro. for durability sake 15-50 for infill. feel free to make adjustment's as I made it 10mm spaced for me. in black...
thingiverse
I respaced them to me more even and the hole for the mag I took 1mm off the inside space to get a little tighter but not where you take the whole thing with you. I thought the walls of the mag holders were a little small so I beefed them up. By...