can of whoop 3d models

Small maintenance base to connect usb to tinywhoops and keep them flat. ...By using this i can connect betaflight and do accelerometer calibration. ...I designed thjis for my Mobula 7 (75mm) and Beta65s (65mm), they both fit very well.

You can either print the frame and ducts separately and then assemble them by screwing them together. ...Alternatively, printing them as a single unit is strongly advised because it produces a significantly more robust result.

I'm excited to create a small, holey board so I can securely attach equipment to oversized FCs. ...If I don't, it'll just drift around and cause frustration for everyone involved.

i can't find angled usb cable so this is my solution for accelerometer calibration Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 50 Category: R/C Vehicles

... ...Compatible with 0603/0703/0803 motors, and boasting a battery compartment tailored specifically for the betafpv 1S 11mm wide battery, this design can accommodate up to 31mm props. No supports are required, but printing it upside-down is essential.

This device features an opening where twine can be tied, allowing the gate to stay upright without needing stakes; users can also hang the gate on walls using stake holes. The device comes in two and three foot sizes. A colored electrical tape stripe...

Remixed this awesome boat into a catamaran for some high speed, low drag boating. ...Added battery holder, FPV camera holder, and flight controller holder. FPV camera holder will fit the camera/VTX combo that you can get on amazon for around $15.

... for the Medlin Drone Whoop FPV Gimbal, the collection will grow over time. ... Whoop FPV Gimbal can be found here: https://www.thingiverse.com/thing:5733796 Spartan Camera Hat is a modification of this thing: https://www.thingiverse.com/thing:3026848

Rather than messing with bits of wire, stick the paper gate artwork to some 3 mm Depron and print 2 of these.

Instead of fiddling with wires, attach the paper gate design directly onto two sheets of 3 mm Depron and then print them out.

Instead of wrestling with wires, simply attach your paper gate design directly onto a sturdy sheet of 3 millimeter Depron material, then print out two identical copies.

Modification of the existing design from Thingiverse, adjusted to be slightly more refined and minimalist in appearance.

The height of the human body measures 65 inches. ...A remarkable fit indeed, the inner dimension is precisely 45 millimeters.

I had built a diminutive yet robust frame a while back that I was particularly proud of.

Customized version of https://www.thingiverse.com/thing:3806549 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3806549

... of 3D printing technology. To achieve its sturdy structure, the following print settings were employed: a layer thickness of 0.3mm, two outline layers for added strength, three solid layers for stability, and a moderate infill percentage of 20%.

Customized version of https://www.thingiverse.com/thing:3601191 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3601191

Customized version of https://www.thingiverse.com/thing:2707851 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2707851

This design is optimized for use with Nano-Tech 300mAh 2S batteries and is actually a reworked version of a previously created resource.

Customized version of https://www.thingiverse.com/thing:3806549 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3806549

Customized version of https://www.thingiverse.com/thing:3806549 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3806549

Customized version of https://www.thingiverse.com/thing:3601191 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3601191

Simple holder to hang up ur HullaWhoop Ring on the Wall. ...Especially for 40 mm thick weighted Hullas with a diameter of 100 cm.

This is a remix of Albert Kim's remix of the simple TPU canopy for micro cam's like the runcam nano 3. This remix adds holes for 2mm screws and an extra hole in the back to be able to change the camera angle. ... This canopy was made to be used...

... ...Next, I was able to remove a significant portion of the holder's structure. This strategic modification significantly reduces overall weight, facilitates effortless battery adjustment during hook-up, and streamlines the in/out process of the cell.

A versatile creator transforms everyday smoothie straws into an extraordinary hexagonal whirlygig, injecting a dash of innovation and creativity into the project. ...By printing the elbow connectors with their channels facing upwards, they provide a...

... part of the motor. In some instances, the motor overheats and softens the PLA, causing the motor to spin out of control. To resolve this issue, a small amount of hot glue is applied at the end of the motor to secure it firmly against the support.

Also modified the frame to allow the battery connector to fit instead of relocating to the top of the flight control board. it is a tight fit with the stock battery so also added a file for larger batteries which moves the bracket forward using the...

Rather than have tiny, coloured end caps to keep track of charge state, like I do with my XT60s and XT30s, I made this little rack to stand them in. ... Holes are 7mm x 17mm.

This object is crafted using the innovative platform of Tinkercad, a web-based tool that allows for easy editing and manipulation online at https://www.tinkercad.com/designs/dJm85n8on1j.