camera picatinny rail mount 3d models

I couldn't find a easy rail mounted Pi4 case with camera holder. So I took inspiration from three projects on here. Original Sources: https://www.thingiverse.com/thing:3079477 (Based design off of) https://www.thingiverse.com/thing:3426764 (Cam...

This camera rail-mount / holder allows you to change the height and Z-axis rotation of your camera. Using the joint on the camera you can also change its pitch. ...The rail can be mounted vertically on the leg/side of the enclosure. You can mount the...

Reach the X stop by adding X cable relief and supporting the EZABL mount. ... The camera mount collides with the EZABL mount, blocking access to the X stop.

Picatinny Scope Mount 30mm Diameter Mounts directly to a Picatinny rail, providing a rock-solid base for your scope. Includes one M4 nut and one M4x30 hex screw for attaching the mount to your rifle. ... The mount itself requires four M4 self-locking...

Since I needed to capture top-notch time-lapse footage from my Creality CR-10 printer, I crafted this camera mount that slips neatly over a 20x20 rail. This allows the mounting of a standard 1/4-20 tripod ball head, such as this one...

Since I wanted to get top profile view time-lapse from my Creality CR-10 printer, I designed this camera mount which will slip over a 20x20 rail and allow the mounting of 1/4-20 standard tripod ball head like this one http://amzn.to/2sRYcwj to allow...

This allows you to mount two CSI/DSI to HDMI adapters on your DIN rail, preferably next to your Raspberry Pi. As this is a passive adapter without any electronics involved which just routes the wires onto a HDMI plug, it will work for both camera...

Mounting ring for rifle scope or airsoft in diam 30 mm with picatinny rail

Scope mount for 25.4 mm scopes suited for picatinny rail. Reguires 2x M4 and 4x M3 for each mount. ... Designed using Microsoft 3D builder and repaired with MeshMixer.

I made a Mount to attach to the 2020 Aluminum Front Rail because I did not have the same corner bracket to mount to. I made 3 versions with different angles for flexibility of mounting. ... I ended up using the 30 Degree mount.

To detach the camera from its original mount, locate the black tabs situated on either side of the camera body and press them downwards to release the device. Once released, snap the camera into this custom mount. Please note that I'm not entirely...

I've taken the original designs from Thingiverse, specifically the remixes found at thing:2600507 and thing:3476490, and combined them to create a brand new camera mount that's sure to impress. ...This innovative design brings together the best features...

An extension for the Ender 3 Playstation Eye camera mount can be found here: https://www.thingiverse.com/thing:3217226. This modification simply lifts the camera upward, offering two options - an angled and non-angled version. I prefer the angled...

I wanted to put my Wyze 2 camera so I could see the print dead on when the printer was printing but I found the "fingers" on Jaytorino's mount flimsy and didn't hold on well. My previous camera was the Logitech C270 and I liked the mount that I had...

A simple flashlight mounting bracket to mount a 30mm flashlight to any picatinny rail on a firearm or airsoft gun. ...Prints in 2 parts and requires 2x M5 bolts for mounting to rail, 2x short M3 screws to tighten clamp and 1x long M3 screw for the...

Custom 26mm Picatinny Rail and Handlebar Mount for a Variety of Accessories. Made from High-Quality ABS, This Modular Design Allows for Easy Installation and Modification to Suit Your Needs. A Single Application of Acetone Is Sufficient to Secure the...

However, if you're using a very long camera, you might prefer the longer file instead. To print this model, I suggest printing it with supports and upside down (inverted). It should fit snugly onto the Tarot Gimbal rails. If you don't have access to...

this is a picatinny rail with mounting bracket for a 25.5 diameter scope

A 25mm Picatinny mount enables attachment of a scope, bullet camera or infrared light source to a gun. To ensure a snug fit, sand the mount slightly smaller than the rail and cut its mounting ring parallel to the barrel. Fasten with 2x2mm screws or...

... of the Flat Drift mount model and a picatinny attachment found on Thingiverse. All I did was split the model in tinkercad and attach the rail mount base to the Drift mount. ... All credit goes to the original authors who created these designs.

... 88 by Unworldly777. ...I made some minor modifications for better positioning and clamping strength (added two notches for the part bridging barrel and magazine tube). I also added two picatinny rails one on each side for additional/removable parts.

Built for an impending project, its scope awaiting clarification. As has been customary, all monetary support via PayPal is most graciously received: http://tinyurl.com/mg9k4kf. This generosity assists in financing my 3D printer and reinforces the...

Picatinny rail for Cobra Crossbow. ...With this rail u can mount a Forward Grip without drilling into the frame. ...

This component serves as the mounting point where the 45 Degree Offset Picatinny Rail attaches to the rail itself.

I designed a custom picatinny rail to mount my IR flashlight, and it turned out great! Now I'm eager to test its durability under recoil from a .308 rifle, but for now, it should work perfectly fine on my Airsoft gun. The rail is optimized for 30mm...

This is a unique plaque designed specifically for mounting on Picatinny rails. To make it easier to print and assemble, the design consists of two distinct components. ... Simply attach the parchment scroll to the base piece by gluing it directly onto...

... .15 - .20Infill: I printed at 100% for stability (probably overkill)Notes: I printed this using Creality Print. ...I added supports to the inside of the rail inserts. My print came out very snug (aka perfect fit) as I slide it into the rails.

... a 32mm ID that fits over BASR (Bolt Action Spring Rifle) bull barrels, like the Action Army T-10. ...Equipped with Picatinny rails at 0 and 90 degrees, users can attach forward-facing scope cameras and rear-facing GoPros for enhanced performance.

I updated the design with a standard picatinny mount added to the bottom for easier installation and placement onto rails, as well as printing with ABS material. ... Print Settings: Printer: Home Built Rafts: Not Used Supports: Not Needed Resolution: .2...

Picatinny rail optic mount designed to hold a one inch cylinder portable battery. I would also recommend adding the level in the link below. Cylinder Battery: The link for this battery is no longer available. ... Levels:...