camera desk stand 3d models
359998 3d models found related to camera desk stand.
thingiverse
More information and photos of this project can be found at: https://daumemo.com/diy-camera-desk-stand/ You may also be interested in my other projects: Dremel Drill Press [![Dremel Drill...
thingiverse
To make this stand, you'll need: 2 x 1/4-20 UNC bolts that are 1" long for the main camera mount 2 x 1/4-20 UNC bolts that are 1.5" long for the two tilt mechanisms 3 x 1/4-20 UNC nuts 1 x 1/4-20 washer The photos should give you a good idea of how...
thingiverse
As the new GoPro Hero 9 supports webcam mode a desk stand for the GoPro is a good idea. or use older GoPro as webcam via the hacks / mods that are out there for it. UPDATE:: Added a V2 version that have longer and wider legs and a wider base,...
prusaprinters
Desk stand for GoPro. As the new GoPro Hero 9 supports webcam mode a desk stand for the GoPro is a good idea. or use older GoPro as webcam via the hacks / mods that are out there for it. UPDATE:: Added a V2 version that have longer and wider legs and...
pinshape
You see my initial design captured in this photograph, and it does indeed function. However, upon completing this project, I discovered that the components posted here offer a superior solution. ...The four-foot-long dowel rods with a half-inch diameter...
thingiverse
The main problem is in camera holder: M6 screw could damage the camera, 1/4" is preferrable. So it is. Camera holder: support 1/4" screw (for example, type D here: https://aliexpress.ru/item/1005001453291034.html). Suitable for Nikon camera. Desk...
thingiverse
This is a straightforward 1-axis desk stand designed specifically for cameras. It's perfect for mounting action cams, small DSLR cameras weighing around 600 grams, microphones, or even your mobile phone.\r\n\r\nI frequently use it when filming solder...
cults3d
This is a simple 1 axis desk stand for cameras. You can mount actioncams, small DSLR cameras (~600gram), microphones or your mobile phone onto it. I like to use it if i want to film solder work, for this it works quite nice. You will need 1 M3...
prusaprinters
A dead simple desk stand for the Articulating Raspberry Pi Camera Mount which can just stand by itself or be attached to a wall using adhesive.This project only contains the files for the stand itself, articulated link and camera housing must be...
thingiverse
The Ubiquiti G3 Instant has a small base and is easily knocked over. Simply setting it on a shelf doesn't allow and vertical adjustment. ... This mount is a little more stable than simply setting it on a surface and allows full articulation up or down...
thingiverse
printer desk, I designed and printed an STL file using my UP! 140x140x135mm printer. The base is curved due to the size limitations; however, it works well and remains stable. To print, adjust Z dimension by 10%, turn upside down, and use no raft...
myminifactory
... features numerous 4mm holes that serve as positioning locks, allowing the arm to be bent in 5-degree increments for optimal flexibility. For more information and captivating project photos, visit https://daumemo.com/diy-camera-desk-stand/.
grabcad
To go in stand mode you just lift the board and with lifting the left side higher like the right one the Stand desk is locked on top position. To go in sit mode lift the right side of the board and push the left side down, and the desk is going down...
thingiverse
I just scaled up the stand from Thingiverse's http://www.thingiverse.com/thing:1248484 to a whopping 14cm. The tiny original was toppling over, since I had my camera positioned quite high. My options were either to attach it to the table or enlarge...
thingiverse
This is a screw into your desk camera stand. I recommend abs filament. This is for presentations on a flat surface. the little slot on the top are for rubber bands to hold your computer. ...
thingiverse
This is a replacement mount for a desk mounted microphone arm so it can be used as a mount for devices or hardware using a standard camera mounting screw.
cults3d
This multi Part 3d Model is an Adjustable Camera or Webcam Holder that is perfect for a desk or for online meetings. It has a modern and hexagonal design and the height can be adjusted to 5 heights. The end can either be one of the 2 included...
grabcad
Camera Stand AssemblyKindly like and give feedback in commentsfor Q/A & project reach out atazanch04@gmail.com
grabcad
A two-axis camera stand that allows for simultaneous movement along the vertical and horizontal planes, or the X and Z axes, is used to hold the camera in place.
thingiverse
... that ovals require additional support on the shelf fronts, whereas standard supports work well without any issues. The 3D printed camera stand was created using black PLA material, providing a sturdy and durable base for the Octoprint HD camera.
thingiverse
... out smoothly. On a related note, I'd like to extend my gratitude to akira3dp0 for designing the bolt used in the camera stand, which is available on Thingiverse. ... https://www.thingiverse.com/akira3dp0 https://www.thingiverse.com/thing:1460364
prusaprinters
About the model:This is a universal camera stand that support the majority of the small cameras. What you need:About 300g of filament2 or more rubber bands to secure your cameraInstructions and assembly:It is very easy to mount together the camera...
thingiverse
This is an ugly camera stand that uses a diving weight (or something else in the box ) as a counter weight to the camera . I wanted the smallest possible foot print and I also wanted to be able to use my web cam with my computer . So I came up with a...