calibration ender 3 v2 3d models

A redesign of the Ender 3 v2 attachment for bed and Z chains by wku_wake. This design utilizes the hardware from the z stop mount after adding a bed level like the BL Touch.</p> <h3>Print Settings</h3> <p><strong>Rafts:</strong></p> <p>No</p> <p...

I upgraded my Ender 3 V2 with a Micro Swiss Bowden Extruder recently. I also had the Filament Sensor Kit from Creality installed. Then I noticed, that the intake of the new Extruder and the outtake of the filament sensor does not match. Therefore I...

The roller is angled to better support filament spools mounted slightly to the rear such as the deault Ender 3 v2 top mounting arm or my (more compact) rear mounted spool (https://www.thingiverse.com/thing:5330574). The angled roller also keeps the...

A tray for the Raspberry Pi to attach to double rail extrusions behind the LCD screen of the Ender 3 v2 or any 3D printer using aluminum extrusions. Use a t-nut in the top right to stop it sliding. I printed it on it's edge with a brim for...

Ender 3 V2 Dual Front LED Light. IDEAL FOR DUAL-Z AXIS MOD on Ender3 Also suitable for other 3D printers with similar frame 2020 extrusion frames, even bigger ones, just need to scale the "DualFront_LED_Profile_V3" model in Z. Notice to print a...

I think the Ender 3 V2 has similar ones. ...Found the file at <a href="https://www.thingiverse.com/thing:4737883">https://www.thingiverse.com/thing:4737883</a>.</p><p>It printed great, but I wanted a slightly tighter fit and I made the slope steeper to...

Hello this a support free Ender 3 v2 filament guide with built in mount for inline runout sensor remixed from **RedSoda** remix of **kruselandon12** and originally from **Holspeed**, all credit to them! It is made specifically for this sensor by...

This is a remix from https://www.thingiverse.com/thing:398515 With the Ender 3 V2 the belt tensioner conflicts with where the mounting side on the right would usually line up so I redesigned the back mount to go out just a tad to fit around the...

This SD Card holder is for the Ender 3 V2 machine The Card reader holder opening is 11mm X 35mm and is designed to stop the reader from going all the way back to allow room for the ribbon cable and also be far enough forward at the front to allow for...

This housing uses the original Ender 3 V2 power switch which is relocated to the front of the machine. It is situated so when the print is done it turns off the machine. Some rewiring will be required. If you are unsure of your ability to wire a...

I modified Chris's test to fit the Ender 3 V2. It is designed to work within the 235x235 bed and prints at 220x220 so it stays away from any clips that are used to hold the bed in place. Edit: You may need center the model and then shrink to 99%...

Ender 3 V2 lead screw support to move the support onto the vertical 2040 bar from the top 2020 bar. I needed this part as part of a dual z-axis belt tensioner system to accomodate a GT2 pulley, but will work for general lead screw stablization...

Since I have my Ender 3 v2 inside of a common Ikea Lack setup, I didn't want to open the doors of it every time and fumble inside of it to start a print job, so I ordered a longer cable to the control display unit (10 pin, 1,6m) and a extension...

Remix del siguiente carro Satsana para ender 3 v2 https://www.thingiverse.com/thing:4623647 La idea a la hora de hacer este diseño es tener una pieza que se ajuste a la placa del carro modo plug and play, para hacerlo todo mas sencillo a la hora de...

Since I have my Ender 3 v2 inside of a common Ikea Lack setup, I didn't want to open the doors of it every time and fumble inside of it to start a print job, so I ordered a longer cable to the control display unit (10 pin, 1,6m) and a extension...

I was uncomfortable with the way the filament reel on my Ender 3 V2 was turning on the spool holder. So, I designed this adjustable spool holder which holds the reel centrally, whilst accommodating various sizes of reel. Will fit reels with inner...

I just bought my 1st 3D printer, a Creality Ender 3 v2. I did not like the way the filament was pulled at such a sharp angle into the extruder. So, I designed one that I like using TinkerCAD. It uses a common 608 ball bearing. I included a thumbscrew...

https://www.thingiverse.com/thing:5398100 Improved/Compact Oreo knob for the Ender 3/Pro/V2/S1 encoder knob. Requires no glue. Fits onto the rotary encoder instead of existing knob to stay compact. 6/7/22 - Slightly reduced size of pegs,...

# Ender 3 V2 LCD Mount Left I printed a left LCD mount from Thingiverse that had multiple makes and comments saying "perfect fit". It was a perfect waste of filament and time. So I took half an hour to replicate the original right side mount from...

The hotend cover is designed to re-use the existing Ender 3 V2 fans and the adaptor plate is compatible with the Creality BL-Touch ABL kit.The magnets used are round 6mm x 3mm. A small drop of CA glue is all that is required to install them into the...

This is a filament guide for an Ender 3 v2 that was originally designed with a Bowden Extruder in mind, but if you go Direct Drive and rotate your spool, it'll still work to color filament (End cap won't be needed, but still handy to hold the marker...

This is a rough first attempt at a hot end housing for the Ender 3 V2. Pre tap the holes with an M3 tap and for the fan screw bosses, thread the screw in carefully first then back it out and install the fan. Print as it sits on the printer with...

Simple mount for a Wyze V2 Camera to an Ender 3 I used longer SS socket head capscrews to mount into the existing holes. Doing this allowed me to add bosses and have a strong mounting area. If you want to use the existing screws you may need to...

Remix of Screen mount / Support écran Ender 3 V2 by Justbio - https://www.thingiverse.com/thing:4708037 I needed to move the LCD screen a bit down because of other accessories that are mounted on the X-motor mount. I moved the screen holes a bit...

A simple safety pin that prevents filament spool from falling off the Ender 3 V2 when you're working on your printer and you have to lean it on its "back". I've had filament spool fall off the holder 2 times and it was scary so I made this simple...

[Ender 3 V2](https://amzn.to/2MddE5f) Y-Axis Stepper Motor Damper Mount remixed from the design by: [Ra1ns](https://www.thingiverse.com/thing:4591114) to fit my specific dampers and provide clearance for full retraction of the Y-axis. My dampers:...

This is a bolt in cable support for the rear of the Ender 3 V2 that provides support for the main cable run to the Z axis uprights/ hot end/extruder and X axis stepper. As standard this is unsupported and rubs against the edge of the frame as the...

A endoscope mount for an ender 3 v2 inspired by https://www.thingiverse.com/thing:4742800, but that didn't work for me as my fan cover has round roles, so I designed something that clips onto the sides. See the picture for slicing orientation. ...

When printed in good quality PLA, 0.12mm resolution, 100% infill, 4mm brim for adhesion (waiting for build plate to cool completely prior to removal), no supports, laying on the flat side, it ended up fitting perfectly on my Ender 3 V2. ...I love it.

We recently installed an Ender 3 V2 in our off-road camper and with space being at a premium, I tried to make it as compact as possible. The X-axis adjustable tension mechanism stuck out much further than I would have liked, and would catch other...