calibration ender 3 v2 3d models

Wire strain relief on an Ender 3 V2 and Ender 5 Plus. Will work with other Ender machines. ... Best used with the Duke Doks V6 BMG mount: https://www.thingiverse.com/thing:4808299 Print with supports everywhere.

Eine Führung für das Filament vom 3D-Drucker, dass in das Alu-Profil vom Gestell vom 3D-Drucker Creality Ender 3 V2 gesteckt wird und so ein durchhängen des Filaments im Bauraum verhindert und gleichzeitig eine saubere Umlenkung des Filaments in die...

I made the model to fit the ender 3 or pro.

A Wyze cam mount for my Ender 3 Pro with a handle and more sturdy holding.

I made some modifications to adapt it to the ender 3 pro.

piastra per bmg in direct per ender 3 pro o 3v2 con bullseye o stok

Here is my cover for the Ender 3 with the Chinese Logo.

Maybe I'm doing something wrong, but on my Ender 3 v2, the Z-axis limiter sits too high when I'm not using the glass bed. I usually loosen the bolts and slide it down a little if I need to, but there is a small plastic tab that has to be maneuvered...

This is a stand off for mounting my Ender 3 v2's power supply on the underside of my Ikea Lack enclosure. Print two PSU Secures to the mounts with 4 m3x8 cap screw. The mount then is secured to the enclosure by some screws I found in my garage....

... the right side. For right side optional drawer see: https://www.thingiverse.com/thing:5138213 or https://www.thingiverse.com/thing:5138213 It's my first remix ever, so any suggestions are welcome. Printed and fitted on my Ender 3 V2 Neo.

Modified the Eva Carriage so that it fits an Ender 3 V2. ...It uses the HextrudORT direct drive.</p><p>The uploaded design is modified so that it fits an Dragonfly BMS hotend and BL-touch.</p><p>&nbsp;</p><p>I uploaded the Fusion and STEP file so that...

I wanted to adapt this design originally by Swarti to work with my Ender 3 V2. The original sat a few mm to low to actuate the switch. I doubled the thickness where the piece attaches to the printer rail and it brought up the switch lever to the...

Modified original design to allow the model to lay flat on the bed of the Ender 3 V2 so it can be printed without supports. Also added Wii logo to front of the stand. ... Filament: 1.75 PLA Glass Blue Inland Layer Height: 0.2mm Wall Thickness:...

This is for ender 3 v2's inside of an enclosure after the PSU has been moved outside of the enclosure.&nbsp;Requires some long M5 bolts, longer than stock M3 bolt for mounting stock Y axis endstop housing, and some GT2 idler pulleys (one toothed one...

Holder for shutter switch on Ender 3 V2 X-axis. ... Parts for Shutter Switch: Micro Switch:...

My recently acquired Ender 3 V2 had an issue where the X axis home position was over the edge of the bed. I was trying to print a panel that was pretty much the full width of the surface when I discovered this. The easiest way to solve the issue...

I discovered a crack in my original x-tension housing, so I decided to make a new one, but based on the original tension system of the ender 3 v2. I also made it thicker and more robust then the original. If you need a longer version for "longer"...

Yet another remix of the Satsana Duct for Ender 3 v2 by x4runnerGunnerx : https://www.thingiverse.com/thing:4623647 I added the BTTouch bracket I used previously from Madness1561: https://www.thingiverse.com/thing:4584071 I cut out a bit of the duct...

This is a X-Carriege for the ender 3 v2  with the mod  of linear rails (MGN12H), its very simple but works...

I wanted to mount my PI Camera from the x-axis and found HanKimMN Ender 3 V2 X Axis Mount. However, I have the CR Touch installed, and the head couldn't contact the limit switch. To address it, I took the same general design, and cut out portions...

I needed to put my Ender 3 V2 Y-Axis endstop further than it originally is, so I had to remix one I found to achieve that.Keep in mind that the adjustability is not that great, as at some point (unless you modify your Y Stepper mount) your bed will...

This is a mount designed to fit over and clamp to the X-Axis tensioner on an Ender 3 v2. It allows the camera to follow the Z axis (from the R side of the machine) as the part prints. If there is interest, I'll be happy to post another version...

Holder for shutter switch on Ender 3 V2 X-axis. ... Parts for Shutter Switch: Micro Switch:...

Remixed multiple things here to get the set up I wanted on my Ender 3 V2 with the Black Knight linear rail kit using stock fans. Mini Satsana remixed to include endoscope mount. Adjust BL touch cover so fit within mount and cooling duct and...

I discovered a crack in my original x-tension housing, so I decided to make a new one, but based on the original tension system of the ender 3 v2.I also made it thicker and more robust then the original.If you need a longer version for "longer"...

... wouldn't slide in the base without massive force because of the rubber feet that are on the camera so I also made notches to accommodate. I added spring seats where it mounts to the bed. I also added the text "Ender 3 V2" on the face of it.

Modified original design to allow the model to lay flat on the bed of the Ender 3 V2 so it can be printed without supports. Also added Wii logo to front of the stand. ... Filament: 1.75 PLA Glass Blue Inland Layer Height: 0.2mm Wall Thickness: 0.8mm...

Replaces the stock drawer on a Creality Ender 3 V2 Printer. Fill it with a raspberry pi and other electronics such as PSU Relay. Mounting is easy, just remove the cap from the right extruded aluminium profile, and the Y tensioner. Slide the original...

This is a drawer-based mount for a BTT Octopus v1.1 board on an Ender 3 v2 printer. This is a rough work-in-progress, and I haven't tested this current version on my own machine, so buyer beware. You'll need to remove the stock board mount and tool...

Was struggling to find a good DTI mount for my Ender 3 v2. I didn't like the mounts that fit over the fan shroud because it kept moving around. This bracket fits into the pre tapped holes where a BL touch is normally fitted. The diameter of the...