calibration ender 3 v2 3d models

... contribution. ...:) I made a IKEA (Type: L1324, 21777) LED-holder for Ender 3 v2 that slides nicely in to the V-frame. Brims was necessary or else it popped of from the bed. ... If anyone has tips and trix to make it better, please let me know.

BL-Touch mount for the Ender 3 V2. I made four version, two round screw and two nut head screw version. The print is support free. Probe offset for the firmware: X = -42, Y = -10 Z-offset is -0.96 for me. ... Additional parts needed : M3x6...

This is a divider that will fit in the larger section of the drawer under the bed of a Creality Ender 3 v2. Each segment has it's appropriate size etched into the bottom. ... Remixed to fill the entire length of the drawer, and not knock the handle...

If you have direct drive and the extruder stepper space is empty, you can use this as a cable guide on your Ender 3 (v2). ... If your printer is inside an enclosure i advise to use heat resistant filaments like: ABS/ASA/PETG

... from Leroy Merlin, but can surely be used for other lighting fixtures. ...I chose this model because it is light and has the ideal length for the Ender 3 V2, I glued the mounting clips but they can eventually be screwed by making a hole on the support.

These are direct drive mounts for Ender 3 V2. These mounts are for the default hot end. One is for the default single gear extruder and the other is for the dual gear extruder. ... To install, remove the spacers of the rollers, then fix the mount...

Flipped case for the Creality Ender 3 V2 for better access to mainboard. First thing I tried to print in PETG. It's not perfect, but it is functional. Some parts got unstuck while printing, had to adjust 2 holes with soldering iron. 3x5x5...

... Used the Cable Chain Management from here. ...Cudo's for this. https://www.thingiverse.com/thing:4794723 Used the Cable Management from here. Cudo's for this! Perfect and Complete Cable Chain Management Setup For Your Ender 3 V2.

Ender 3 v2 spool holder with bearings, fully printable. also has a removable stop at the end to prevent spool from accidently falling off the spool holder. Need to manually free bearing and apply lubrication if desired. ...I added a Spacer that is not...

Simple little part to cover the Ender 3 V2's Z screw - the filament passes past it very close and I didn't want filament to be hit by it. ... It fits over the brass bushing and there's little notches for the screws either side.

Designed to fit Creality Ender 3 V2 Neo but can be used as standard container without attaching the rails. ... 2 container sizes (mm): 135L x 40W x 25H and 135L x 40W x 40H Caution: When used on printer, keep all items below build plate surface to...

This is a tool drawer for the 40x40 aluminium extrusion used on Ender 3 V2. Just remove the end cap and pop the drawer in. There is room for ten nozzles, nozzle cleaning tool, nozzle swap wrench and all the Allen keys that came with the printer. ...On...

My PS Eye mount for Ender 3 v2. There is no need for screws. It slides right to the main 4040 profile of the base and the camera goes on the top of the mount. ...The camera base should slide right into the top of the mount and happily sit there.

Case to mount a 16x2 LCD on an Ender 3 V2 I use it in conjunction with the LCD1602 I2c display (0.1.0) plugin on my Octoprint server Mounts nice and neat above the factory display Feel free to use/ modify

Replacement knob for the ender 3 v2 LCD. The original is small and flat, I needed something knurled, a little bigger and with a spot for the finger to rest for quick turning. Prints well upside down, shouldn't need support but just in case you...

These are 4 separate designs of customisable extruder knob for the Ender 3 V2 base on the stock extruder knob. Designed in SolidWorks. Both STL and SLDPRT files are available for all. ... I suggest printing large side facing down as it...

... but bltouch will be mounted 3mm higher. ... Original worked great with stock Ender 3 v2 hotend, but I replaced it with all-metal one which is slightly shorter for some reason and bltouch probe collided with bed.

I needed a dual Z bracket for my Ender 3 V2, but without the need of extra hardware for mounting it. The only extra hardware needed is the nut for the leadscrew. ... The model is oriented so it does not need supports.

Electrical boxes that slide into the front of an Ender 3 V2 and Pro, Designed for OEM Creality mainboard and a Raspberry Pi 4 and it has a mount for a buck converter, the lids fit a 80mm computer fan for an extra cool and quiet operation, you will...

This is an adapter to be used with the original spool holder of Ender 3 V2. I have limited space above the 3D printer where the original holder is fixed. So, this thing could be used together original holder over a table. ...I'm using beside de...

I made some modifications to be able to adapt it to the ender 3 pro and v2 or other bed with the same chassis. ... I strongly advise to print the model with a resin printer,the model requires a lot of details in the teeth.

This is a replacement drawer knob for the Ender 3 v2 drawer. I suggest to print in PETG since it is more flefible and PLA will break when you push it in the hole of the drawer. Category: 3D Printer Parts

Mounts to the M3 holes on the Ender 3 V2 X-carriage, with the same probe offset as the classic mount by Jkostenov. Fits with the stock fan duct as well as the Mini-Me V4. Probe offset: X-42.00 Y-10.00 Thanks to Jkostenov for creating the original,...

My PS Eye mount for Ender 3 v2. There is no need for screws. It slides right to the main 4040 profile of the base and the camera goes on the top of the mount. ...The camera base should slide right into the top of the mount and happily sit there.

This is a simple bed levelling design. ...The Gcode included is for the ender 3 v2 bed size. stl is included so you can change the size to your bed. Its one layer high at .2 resolution. takes about 5 min. ...Enjoy!

... the way, so I made this. ...It is mountable on the Ender 3 V2, and I'm not sure about the pro. Definitely not the original, though. It is made for the raspberry pi 4b. ...Thanks to https://www.thingiverse.com/thing:4665097/ for making this originally!

This is a remix of this :https://www.thingiverse.com/thing:2932344 for the Ender 3 v2. I took off the left hand side and also took off the side notch because for some reason it made the z-rod bend to the left looking it behind. ... Follow the...

Fan shroud/hot end cover for ender 3 v2 neo with lightweight fan holder for spider hot end. This one: https://www.thingiverse.com/thing:6029098 Needs 1 m3 heat set insert for the screw hole. ...Painted the "Y" design on the front red to make it...

... haven’t printed yet if anyone wants to print and let me know i can adjust. ...`It should fit the screws that lock in the slots. I took the idea from this https://www.thingiverse.com/thing:2757810 design added it to this to fit the ender 3 v2. ...

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. STL file contains left and right facing brackets. ... Print both or delete the one you don't need in...