calibration cube ender 3 v2 3d models

WARNING: The current version might have the Stealthburner bump into it at max travel points (not in regular printing...

  Inspired by https://www.prusaprinters.org/prints/40182-geodesick-rgb-led-spheres but designed completely from scratch to use a more consistent way of assembling the facets together.Additional components required - 10 6mm * 2mm Neodymium...

This pack contains over 3,000 bat wing/hanger/sign/halloween decoration STLs generated from the top 3000 first names in the UK. The pack also includes PNG renders of each bat. The bat is approximately 50mm tall and 110mm wide. For long names the...

Metal Pieces 1 x M10 x 1.2m Stainless Steel Threaded Rod 3 x 10 Pack 16mm Silver Key Ring 2 x 1.8mm x 2m Chrome Plated Mini Oval Chain 1 x 4 Pack 38mm Silver Solid Ring 1 x 10 Pack M10 Stainless Steel Thin Half Nut 1 x M10 x 20mm Washer Printed Parts...

#To flash your firmware see https://www.thingiverse.com/thing:2783450 For more information and the links I got my info from see below: - https://www.thingiverse.com/thing:2783450 - http://3d-maker.info/switching-to-ramps-1-4-wiring-anettronxy/ -...

Y holder motor upgrade for Prusa Mk3 Mk3s Mk3s+ Upgrade your Nema 17 mount to improve vibrations, noise, belt alignment and rigidity.→ Easy screwed to panel with strong ruthex M3 Threaded inserts.→ 1mm gap between motor and rear panel.→ x3...

If you have never used Arduino's before or the software to program them you can visit https://www.arduino.cc/en/GuideAdding libraries:Once you have the Arduino software open we will click on Sketch > Include Library > Manage LibrariesOnce there...

The construction of the piece wouldn’t have been possible without the help of Andreas. LINK TO HIS PAGE. (My clip on the left partner's on the right) (Clip compared to model)Lesson Plan and ActivityWith a partner, you will recreate...

We are presenting a new wind turbine device, that is easy to 3d print, it can be made handcraft once it is viewed it components and how they get assembled in a very easy and intuitive view, This system have several pending patents and the device...

3) There are many issues with the current design that needs addressing in the next iteration. I’m only a beginner in electrons, so there will be design flaws. The device is not a 50-ohm impedance match, so there will be signal loss within the design...

For this you need two times dat part-3 and once each 4 and 5.  Part 4 and 5 are ment to hold with carriage bolts to the backrest,...

length, it will protect the cable from the fan blades.Step 3: Place the front guard cover inside a Prusament spool side and glue the fan to the back.Step 4: Place the back guard cover inside the other Prusament spool side and attach it with the clamp...

3. Light Nautiloid Horror Carapace (body) with One Shell Hardpoint, Shrimp Version. This means that this particular body can use two arm weapons, and one heavy carapace-mounted weapon. It also has a scaly ridge along its body. 4. Light Nautiloid...

They work great for the top hinges.3x M3 hex screws & nutsFor the shelf hinges holding the shelf to the pole (tightens the ring).3x M4 screws & nutsFor the shelf frame assembly15x #6 x ½" wood screwsM3.5 x 10 or 12mm should work too (should...

It's then ready to slice.Combining parts in Cura:I haven't been able to figure out how to get Cura 3.6.0 to leave the models in their original locations when they're loaded into the slicer. It always moves them to the center of the build plate or the...

If you look on the balance wheel from the side where you can see the metall nuts, the stud on the spring should be facing 3 o'clock when the pin on the balance wheel is facing 6 o'clock.Now you can slide this assembly onto the rod near the quadratic...

3) Slightly loosen the 2 screws on top of the Metal X-Axis Bracket. You can leave these loose until the very end of the install. 4) Start by removing the V-Wheels from one side. The X-Axis should hang there just fine. 5) Next remove the Eccentric...

... and ZK-SMC02 stepper motor controller.  Also requires a NEMA 17 bracket to attach motor to 3D printed parts (see photos). Additional 1:3 reduction with gears (60 teeth in new dial and 20 on stepper motor). ...280mm 2GT belt is the approprite length.

The mounting characteristics of this lamp is perfect for the Sherman S and the Patton, it has the mounting holes right in the middle of the light which conforms to space requirements and make it more balanced when mounted, it's not too heavy, the...

Dazzling Celestial-Halo band adorns a gleaming round centerpiece of sparkling brilliance, showcasing an astonishing 0.3 carat radiant treasure in stunning precision print detail. Gems shine forth with unparalleled allure: on the Engagement Ring,...

You need a minimum of 3 pieces (or one larger) with a dimension of about 40 x 50 cm each. One of these should be enough to cover all panels but I haven't tested this one in particular myself:</p><p><a...

If you want to make your own medallion, the holes in the grip are 17mm Diameter and 3mm deep. Assembly Guide Grip and Receiver Gather the Grip_Left, Grip_Right, GripScale_Left, GripScale_Right, GripReceiverSidePlate_Left,...

If you are interested in how the product is assembled, see the Assembly chapter.To buy an LED strip and a power supply, I suggest the following link:More expensive and better version (I use this...

This pack contains over 3,000 pumpkin decoration STLs generated from the top 3000 first names in the USA. The pack also includes PNG renders of each pumpkin decoration. The pumpkin is approximately 50mm tall and 65mm wide. For long names the width...

In the images attached to the gallery you will see the recommended orientation for every element to be printed.Gently remove the support once printed. The REDUCTION part is a critical part of the robot. Print is slowly.Features: Google Blockly...

However, that's with the standard 3:2 aspect ratio. In 1:1 (square) format,<strong>a lens that can cover that diagonal also should be able to cover a square with approximately the same diagonal, which would be 30.59x30.59mm</strong>. In infinity:1...

On the bottom of the base, there is a access hole to the IR detector; use this access hole to push the IR detector out through the hole in the base (a pair of needle nose pliers helps with this).[3] Prepare LED StripThe "internal length" of the...

This is great for students to play in between classes, or during break, or anyone who loves a nice chess match. The approximate dimensions of the chess/checker set when rolled up is ~3.5in ø (~86mm ø) x ~ 8in (~204mm). Weighs ~453g (~16oz). This is...

Making relief cuts and trims as I went along to get rid of visible folds and wrinkles.The printable "tools" can help here to get a better grip with clamps.When most of the visible wrinkles in the felt are gone, the glue has set and you are done...

**G-CODE EXAMPLE 3** This exercise begins by testing G-code moves required to successfully eject the print. Please note that the code sets the print head to the rear corner of the print bed (Y changed to 220 for safety reasons). *Part 1: TESTING...