calcifer with light 3d models

I used an Arduino Nano to power a RGB LED that lights up the transparent dome of a simple signal light with wall mount. A hole in the base is reserved for the USB cable connecting the Arduino. In my setup, I paired an ATmega8 microcontroller with an...

The light itself may be pricey, but the cord is switchable and you won't need to replace batteries like with typical tea lights. \r\n\r\nI used Itslitho.com to design my lithophane: https://tool.itslitho.com/#/CreateModel\r\n\r\nLithophane...

I designed this flood light with 365 nm UV LEDs and a matching UV pass filter in mind but you could also not subject yourself to invisible eye damaging radiation and opt for any other LEDs in the visible spectrum of light. If you want to use UV LEDs...

same cover but added rail for laser or light

Holder for Small Lithophane Displays Featuring Tea Light Illumination.

... 02.mm resolution. ...New smaller base and 3 tree heights.Tea light is about 1.45in/37mm in diameter. Used super glue to secure tea light to base and base to tree top.Update: Released a new Gift Box for the set of trees and spare CR2032 batteries. 

Remix of design from DiPT Original files: Darth Pumpkin Vader by DiPT: https://www.thingiverse.com/thing:3144320 Jack-O-Lantern by Makies: https://www.thingiverse.com/thing:167043 idea: Jack-o'-lantern pumpkin with separate stem by eight_heads:...

I designed and printed this for covering the light hole that needed to be covered by the new light fixture.

This is sized for usb cord: https://www.amazon.com/gp/product/B009GUMVKW/ref=ppx_yo_dt_b_asin_title_o00_s01?ie=UTF8&psc=1 litho_light_clip_v2 -- Supports buildplate only, this is slightly larger for Amazon basics USB cable:...

This is sized for usb cord: https://www.amazon.com/gp/product/B009GUMVKW/ref=ppx_yo_dt_b_asin_title_o00_s01?ie=UTF8&psc=1 litho_light_clip_v2 -- Supports buildplate only, this is slightly larger for Amazon basics USB cable:...

Unfortunately, that particular design isn't compatible with the new fan duct, so I started from scratch and added a light refractor to it as well. I'd like to extend my gratitude to https://www.thingiverse.com/gnorbi921 for sharing his brilliant...

To complement this upgrade, I sought a way to integrate a light switch for my LED lights. By importing his feet into TinderCAD, I was able to modify them to accommodate a microswitch, allowing me to mount it discreetly beneath the control panel. I've...

Bambu Lab AMS Light with Tags I combined couple different ideas and remixed them and put them in one to accommodate my needs AMS Light and Tags from https://www.printables.com/model/320939-bambulabs-ams-attached-lightbar and...

The incandescent light bulb symbol is now enhanced with the capability to be illuminated using 10mm standard or 12mm most RGB LED strips, providing ample space for a controller unit. This upgraded version of the symbol also accommodates most RGBW...

Note: The front-mounted light bar tends to wobble with printer movements, resulting in an unsteady appearance. However, this instability does not pose any functional issues. ... This design modification was inspired by a 3D printing project available...

The LED Light is connected directly to the Hot-End Fan via a simple circuit that incorporates the switch. ... Components Needed: - An LED ring rated at 12 volts for the Holder, available on Ebay: https://bit.ly/2DcqoUi - A two-pin Switch from Ebay:...

Christmas tree topper remix gets a LED makeover with standard lights built right in on the back part.\nYou can see from the attached photo how I've added five LED lights into the light holes of this custom topper.\nThe original was printed out of...

I also wanted to have light for the eyes but operate the whole thing with batteries. so a place had to be created for the battery holder and switch. I scaled everything up a bit, changed the base a bit and added a drawer. ...

This Christmas Tree is designed to accommodate a battery-powered LED light measuring 3cm in diameter and 2cm in height. ...The tree's dimensions allow for detailed prints at a layer height of 0.1mm, with one perimeter line and no internal infill.

This is a straightforward cosplay featuring a classic DC 17 blaster pistol expertly paired with a Light Saber hilt. The hilt is designed to be detachable, allowing for versatility in various roles, such as conventions or Clone Troopers wielding the...

... with enhanced diffusion capabilities. ... To achieve this improvement, I positioned the LEDs at a 10-degree angle, thereby preventing them from directly illuminating the paper and instead focusing their light downwards towards the bottom of the panel.

Base with led light for figure made of acrylic. It consists of two parts: The upper one (Top) has a slot to insert the figure, a hole for the switch and a hole for the 12 V input connection. ... The lower one (Bot) is the lower cover that must be paid...

A great stand for your obscure Japanese only Game Boy Light, this time the words are hollow for a more impact view on the stand itself. ...as the previous one comes with detachable arms for storage or travelling, a wall-mount and great angle view.

I printed this on my ender 3 and with this design I put a clamp on a led light remote holder.V2:Will fit most desksV1:Will use less material but have a smaller clamping area.Check out my pintables page:https://www.printables.com/@Jerry_554784/models

Light link https://pt.aliexpress.com/item/32847541766.html?spm=a2g0s.9042311.0.0.2742b90aFbi4gH Board link https://pt.aliexpress.com/item/33049540052.html?spm=a2g0s.9042311.0.0.2742b90aZbNUoK ON/OFF button link...

This cosplay showcases a DC 17 blaster pistol expertly paired with a removable Light Saber blade attachment, allowing for versatility in its use at various jobs, conventions, or when portraying Clone Troopers. ...The detachable baenet features a...

This is a take on a light switch plate with a wall to block some of the motion sensor area. ...this is so I could walk by the laundry room without the thing turning on if the door was partially open.

Project includes: Base Seed holder Grow light arm Now check photo with numbers: 1 - 5m Led Strip Grow Light 5 Red 1 Light 2 - Female 2 pin led connector 10mm 3 - 5m Led Strip Daylight 4 - LED connector 10mm female dc power plug 5- Printed part 6 -...

... that. I went with a snap in candelabra socket with switch from Home Depot and 40w LED bulb. It is very bright. Might be better with a 25w bulb. I do recommend rafts or brims for the roof and roof truss pieces that are open for inserts. ...

Now check photo with numbers: 1 - 5m Led Strip Grow Light 5 Red 1 Light 2 - Female 2 pin led connector 10mm 3 - 5m Led Strip Daylight 4 - LED connector 10mm female dc power plug 5- Printed part 6 - Charger DC 2A 7 - Any Smart Plug Assembly: Prepare...