caged dipole 3d models

RFDesign 900MHz 3dBi Dipole Antenna AssemblyA dimensionally accurate reference antenna model based on the default antenna used with the RFD900x Radio Modem to interface with with PixCube and Ardupilot flight controllers.

The center hole of the dipole fits snugly over the Spiderpole mast and stops precisely at the pole diameter needed to reach a height of exactly 30 feet. A standard SO-239 chassis mount connector is employed for the feed line, ensuring a secure...

My reworked design for a 3D-printable holder for the RTL-SDR dipole kit (or any compatible). ...Prints and looks much better than the previous one, also I tried to make the mounting easier.

RFDesign 900MHz 3dBi Dipole Antenna AssemblyA dimensionally accurate reference antenna model based on the default antenna used with the RFD900x Radio Modem to interface with with PixCube and Ardupilot flight controllers.

This is a center structure for building dipole antennas using window line or ladder line as the actual antenna radiator. I made it to use a BNC panel mount connector for a coax feedline. It could be modified for an SO-239 using most modeling...

This is an upgraded version of my original caged 1104 drone with many enhancements and reinforcements. The bottom plate features: Motor mounts holes reduced for smaller 1104 screws heads Fatten full support arms Added 20x20 PCB holes Added 25x25...

Tuning is typically oversizing the antenna dipole elements (lower frequency) and then trimming the ends to bring up the frequency to the desired center frequency, which is usually the center of the receiving and transmitting band.For more information...

Tuning is typically oversizing the antenna dipole elements (lower frequency) and then trimming the ends to bring up the frequency to the desired center frequency, which is usually the center of the receiving and transmitting band.For more information...

If you're looking for an awesome antenna to upgrade your RC transmitter or other wireless device, building a 2.4GHz folded dipole is a fantastic idea. This project requires some basic skills and materials, but the end result is well worth it. With...

I designed this center structure for constructing dipole antennas utilizing window line or ladder line as the actual radiator. I built it with a BNC panel mount connector in mind for a coax feedline connection. The design could be easily modified for...

This is a 135-degree V-dipole antenna bracket engineered specifically for use with 3/8-inch copper piping commonly found in water supply lines. A snug, self-supporting fit is achieved on a standard 28mm mast. ...Antenna slugs should securely fit with...

I'm looking for a high-gain dipole antenna angler suitable for 6mm diameter antennas, such as those used with RTL SDR devices or similar models. It's perfect for receiving NOAA signals. ...To assemble this design, simply print it flat without support...

This V-Dipole antenna holder is an iteration of a previous design from @derekcz (https://www.thingiverse.com/thing:4664046). ...It has stronger support on the base of the 2 parts holding the antenna and the satellite logo has been swapped o the upper...

This is a basic adapter designed to fit snugly over the rear stand-offs, providing a sturdy base for a dipole antenna on the HyperLite Floss 2 frame. ...Its universal design ensures compatibility with any frame featuring 5mm diameter stand-offs that are...

Basic dipole construction is outlined by Adam-9A4QV in his blog, located at http://lna4all.blogspot.co.uk/2017/02/diy-137-mhz-wx-sat-v-dipole-antenna.html. I needed a mounting system that would allow me to attach the dipole to a piece of wood so it...

Dipole center for telescopic mast, various dimensions of center cone holes. ...6.5-6mm 7.5-7mm 8.5-8mm 9.5-9mm 10.5-10mm Simple and cheap, put wires through holes and tight them with cable ties, then solder wires to coaxial cable.

Dipole center for telescopic mast, various dimensions of center cone holes. ... 6.5-6mm 7.5-7mm 8.5-8mm 9.5-9mm 10.5-10mm Simple and cheap, put wires through holes and tight them with cable ties, then solder wires to coaxial cable.

Feed point and end insulators for a 20m DIY Dipole Kit.  It is designed for RG-58 but RG-8x should work too, coax to be ziptied to it to secure it hanging vertically.  Wires just tie to the holes on each end. ... Printed in PETG, although PLA would...

Made this to use as a reflector for the v-dipole I found. Designed as a friction fit on a 32mm pvc pipe. 4mm copper rod (solid) cut to 53.4cm each. And this is mounted 1/2 wavelength below. Printing: Use abs for all weather performance. ...20%...

This is center piece for making dipole antenna. Uses SO259 connector for antenna attachment. Provides holes for fixing antenna wire and contact screws. I cut it from plastic on CNC milling machine. ...It may be 3d printed too but pay attention that...

It may be 3d printed too but pay attention that you need mechanically strong material. Print instructionsCategory: DIY Summary This is center piece for making dipole antenna. Uses SO259 connector for antenna attachment.</p> <p>Provides holes for...

Lightweight R9 Dipole T Antenna Mount for the Diatone R349 / T-Motor TM-3419 Frame. This attaches securely with 4 zip ties. The hole accommodates a zip tie of maximum 2.5x1.2mm in size. Printed successfully on the Sparkmaker LSA printer, but this...

This centerpiece constructs a dipole featuring a 450-ohm symmetrical feed line, ideal for CQ 553 flex wire use (compatible with other types, reports appreciated). Print both templates and widen holes as needed with a 3mm drill; field day testing...

Jig for making a 2.4ghz folded dipole. This is a great antenna you can build yourself following the instructions at the link below. There is also a cover for it to protect the element in my other things.

This is the key component for crafting a dipole antenna, utilizing an SO259 connector for secure attachment to the antenna itself. Features include holes designed specifically for securing the antenna wire and contact screws. ...The piece was cut from...

This is an array of 16 paperclip folded dipoles that are arranged into a circular pattern for use on FPV drones. The angle of each antenna is 22.5 degrees and each antenna is designed for 5.6 GHz operation. The array should be phased for best...

Lightweight R9 Dipole T Antenna Mount Designed Specifically for Diatone R349/T-Motor TM-3419 Frames. This compact mount secures with just 4 zip ties, making it a breeze to install. The carefully designed hole accommodates zip ties of up to...

The center box for an amateur radio wire dipole antenna BalUn is designed to be mounted at the top of a supporting antenna pole. Printed in PLA is fine for a temporary (portable) setup. For a more permanent installation, it needs to be painted to...

... IT fits on the plastic bar between the two canopy hatches. Has a anti drag slope at the back to stop negative air flow affecting how it goes over the wing. Nice design, by the way, that little aerial holder {T Style 900MHz Dipole Antenna Protector}

I found an excellent dipole center for a [doublet antenna in this thing](https://www.thingiverse.com/thing:4093412). It accepts 450 Ohm Window line and the element wire in just the configuration I needed. My thing adds an adapter to the center...