caged dipole 3d models

These jigs are specifically designed for creating dipole antennas that operate within a frequency range of 1.2-1.3 GHz. They are engineered to work seamlessly with antenna wire measuring approximately 1.6mm in width, as well as RG316 coaxial cable.

I designed this dipole center in Tinkercad based on designs I found here on Thingiverse (https://www.thingiverse.com/thing:2804993) and on other amateur radio and 3D printing websites. As soon as I have the SO-239 connector and balun installed, I'll...

I got the idea from this site: https://www.rtl-sdr.com/rtl-sdr-tutorial-receiving-noaa-weather-satellite-images/ (The software setup and everything is covered there).\r\n\r\nThis thing is basically just a foldable version of this:...

Used as a mounting point for the counterpoise of a dipole. Utilize 1.2mm derailleur cable for each element and trim to 158mm. For the driven element, this dimension begins at the spot where the cable departs from the end of the shield. The...

Dipole antenna 915 mhz for quadrocopter designed with precision and care. In version 2, I utilize a sturdy tube sourced from a reliable 3D printer supplier. The total width of the dipole antenna used is 140.8 mm, with a wire thickness of 1.5 mm^2.

This is a vital component for double/dipole antennas, primarily used by ham radio enthusiasts. It snugly fits typical 4 - 10 m fiberglass poles and is perfect for portable operation & summit-on-the-air (SOTA) activities. Features: * Two vertical...

The central screw is for connecting the connector (hot pole and GND) and the 4 peripheral screws are used to connect up to 4 different dipoles.The project was created with FreeCad (19.x) and the folder contains the .DXF files ready for laser...

This is a tunable dipole antenna mount using off the shelf parts. ... Frequency in the range of 50-500 MHz Parts used: 2 x Telescopic antenna with M3 internal thread 2 x M3 fastener 1 x SMA RF Connector panel mount piece of copper wire Table of dipole...

The central screw is for connecting the connector (hot pole and GND) and the 4 peripheral screws are used to connect up to 4 different dipoles.The project was created with FreeCad (19.x) and the folder contains the .DXF files ready for laser...

Here it is: https://www.thingiverse.com/thing:3877369 UPDATE 4: After a Year of Use, It Fell Off Due to Strong Winds I was shocked when the dipole antenna box fell off my roof due to strong winds after only a year of use! But fortunately, it landed...

This is a centerpiece to build an dipol with symetrical feed line @ 450 Ohms (like CQ 553 flex wire). I recommend to use the new version (NG) with the improved and strengthened relief. It is still designed for the CQ 553 flex wire but may work with...

Recycling Wire Hanger into 2m/70cm Dipole AntennaWe were cleaning out a closet when my wife handed me some wire hangers and told me to go recycle them. I was wondering if I could use them to make some kind of antenna so I researched wire hanger...

This is a dipole / inverted v antenna centerpiece designed for easy integration of a built-in balun. Measuring 64 x 32 mm internally, it provides ample space for small to medium-sized baluns. I've successfully paired mine with a toroidal current...

Remix of Tarboor Piranha Canopy but with with M2 thread in mounting holes and an antenna hole big enough to hold a dipole, or let it pass through to ziptie to the back of the fin. Print in TPU. Normal supports everywhere with support blockers on...

This balun / common-mode choke dipole centerpiece has been designed to accommodate FT-240 and similar-sized ferrite cores. I use RG-58 for winding, but different coax cables or bifilar / trifilar winding can also be used. The toroidal core holder...

This is the center support for a linked dipole. It is made to hang on a 7.2m collapsible fishing rod that can be commonly found on Amazon for $30-$40. The hole for the rod is set at a 60 degree angle to maximize the surface area contact on the rod so...

A tailored version of http://www.thingiverse.com/thing:195435 was made using the Customizer tool at http://www.thingiverse.com/apps/customizer/run?thing_id=195435. The specifications used for this customized design include a cube width of 20.0, a...

you need 95 Nuts Absolut vodka 0,7 liter

Everyday Speed Modeling Challenge

It's simply a solitary die surrounded by a larger cube. ...I would not advise utilizing my G-code file as it contains settings tailored specifically for me, however I am posting them nonetheless for individuals who wish to decipher the anomalies within...

Unleash His Fury Crafted in Cutting-Edge Blender Software

Designed by Grasshopper/Rhinoceros based on mathematical models.

Customized version of https://www.thingiverse.com/thing:2224678 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2224678

Enclosed in a confining structure, there lies a spherical object.

Easier to print on the side

A Ball Bounces Free Inside an Enclosure. People Stare, Wondering How It Got There. ...I Employed Wooden Supports That Came Out Smoothly, Allowing the Ball to Roll Around With Ease.

Customized Version of Thingiverse's Thing:649898 Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=649898. ... Using the Following Settings: Resolution is Set to 0.20 Millimeters The Diameter of the Structure is 20...

This is a customized version of the Thingiverse model (http://www.thingiverse.com/thing:50261) created using Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=50261). The specifications for this unique design include a rose height...

A medium sized vase, has a smaller vase inside that can hold water. There is some bridging and many retractions. Can be scaled as necessary. ...uses around 250 grams of filament.