cable runner 3d models

Sample DAC Cable runner, remixes from https://www.thingiverse.com/thing:1320948

Modified Cable Runner with mounting holes for screws. ... If you have problems with the original STL not being water-tight, the solid variation works perfectly.

This is a short diameter cable runner. It fits 3mm diameter cables with a small amount of flex, with a 3mm wide base. I've used this to wrap cables around tubes (specifically my dew heaters for my telescopes). ...Works great with double sided tape.

Print Settings I use Cura to print these cable runners with the special mode setting "Spiralize outer contour" which gives them a springy feel when assembled. This allows the cables, not the runners, to bear the load while also making them print...

Sample DAC Cable runner, remixes from https://www.thingiverse.com/thing:1320948 Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: NoResolution: 0.15 Infill: 20 Filament: Grossiste3D PLA Category: Computer

I created this to run antenna and network wire in my ham shack.

<p>I created this to run antenna and network wire in my ham shack.</p>

2x HDMI + 1x USB cable clips read more: https://ecency.com/hive-103035/@tibfox/3d-remixed-printed-cable-clips-for-my-15m-hdmi-cables

2x HDMI (7.5mm) + 1x USB (~5mm) cable clips read more: https://ecency.com/hive-103035/@tibfox/3d-remixed-printed-cable-clips-for-my-15m-hdmi-cables

I modeled this specifically to route Astrozap Dew Heater cables (which are 3mm) around the barrel of my telescope and guide scope.

Get ready for a game-changer with this 20-cable version of muzz64's outstanding cable runner, available now on Thingiverse at http://www.thingiverse.com/thing:1471789. ... The latest update to v.02 brings even more strength and reliability, thanks to...

When 16 just isn't enough - a 20 cable version of muzz64's fantastic cable runner http://www.thingiverse.com/thing:1471789 is now available. The updated v.02 model boasts an additional 1.5mm on the mounting tab, providing unparalleled strength and...

Cable Runner different diameters (Smartphone, LAN, Powercord)

Designed these to hold cables on the back of some fixtures from Sam's Club. I printed them with a 0.8mm nozzle to make them strong and printed them fast at 0.3mm layers on an Ultimaker S5. I used a zip tie to hold them in place once after everything...

Flexible filament printer. ...Run cable through it and then insert into the slot.

Came up with this creative way to run the cables from under my desk with a little bit of extra aesthetic All Parts will fit into eachother so feel free to customise however you need

Flexible cable organizers I employed for concealing speaker wires throughout my family room.

Ethernet Cable Runners offer a hassle-free solution for organizing your Ethernet cables, keeping them tidy and easily accessible. They come in a range of sizes, accommodating from 2 to 16 cables per slot, with each slot designed to hold only up to...

Ethernet Cable Runners offer a straightforward solution to keep your Ethernet cables organized, under control and easy to insert and remove. The range accommodates from 2 to 16 cables, with each slot capable of accepting up to 2 cables at once. This...

Three types are available, including a standard type for use along the floor or across a desk without securing, and two other types that allow you to secure Ethernet Cable Runners with a cable/zip tie. Type "T" has slots aligned in line with the...

Cable management just got a whole lot easier with my custom squared cable runner set. With this, you're free to build your own plate from scratch, specifying length, thickness, internal space and all the other settings that matter. This customizer...

A compact runner fits snugly over the Prusa i3's 6mm metal frame, safeguarding its electrical cables with precision bearings. Specifically designed for this task, these small but vital components measure as follows: Bearings details: * Outer...

These cable holders were designed specifically for securing cables behind fixtures purchased from Sam's Club. Using a nozzle diameter of 0.8mm, the prints were optimized for maximum strength and produced quickly with 0.3mm layer thickness on an...

... detaches due to being overfilled. A solution is found by utilizing leftover screws and fasteners to securely hold the cables in place. ...Since the printed part needs some degree of flexibility, it was manufactured using ABS plastic material.

This clip is pushed on your table and allows you to run cables under your desk or hang a bag from it.If the clip is too loose, you can squish a bit of folded paper or cardboard in between the table and the clip to make a tighter fit.

This clip is pushed on your table and allows you to run cables under your desk or hang a bag from it.If the clip is too loose, you can squish a bit of folded paper or cardboard in between the table and the clip to make a tighter fit.

This clip is pushed on your table and allows you to run cables under your desk or hang a bag from it.If the clip is too loose, you can squish a bit of folded paper or cardboard in between the table and the clip to make a tighter fit.

This clip is pushed on your table and allows you to run cables under your desk or hang a bag from it.If the clip is too loose, you can squish a bit of folded paper or cardboard in between the table and the clip to make a tighter fit.