cable passthrough wall plate 3d models

I needed a raiser for that cable passthrough wall plate.70mm x 114mmRaised by 4mmMight be a bit specific… but I hope it helps someone else too !

Exterior Diameter: 1.75 Inches Inner Diameter: 1.5 Inches Flange Diameter: 2.75 Inches Maximum Depth: 5 Inches Minimum Depth: 3 Inches Fits with Friction.

This is a temporary solution to stop my HDMI cable from scratching my fiberboard wall. It consists of two components. Certain sections can be fragile. Modify the diameter in the SolidWorks file to align with your wall's holes. ...The STL file is...

... a smaller option for hiding wires behind a wall for a monitor or wall mounted TV. ...The required hole is 3/4" instead of much larger options. You can fit a standard HDMI cable through a 3/4" hole. This passthrough is capable of handling three cables.

Simple wire concealment device for covering holes drilled through walls to accommodate cables and wires. ...I utilized this to seal the openings created by running network cables through the wall without employing a traditional electrical outlet box.

DescriptionThis 3D Printable Wall Passthrough is useful for passing cables from one side of a wall to another, dressing the hole nicely. The outer diameter is 2 Inches and the inner diameter is 1.6 inches. ...The hole is big enough to fit standard plugs...

... your x and y axis belts are tight and you do not have much stringing or external defects. I designed this to slide cables through the wall easily. ...It is sized for a three inch hole saw and a 2x4 constructed wall with 1/2" drywall on either side.

(The hole down the middle of the screw is the diameter of the cable that comes attached to the dish.)This cable passthrough is designed to assemble around the cable. See the pictures to see how. The attached .M3D and .GCODE files are for a 162...

Used to pass cables through an ikea lack table for enclosures

A cover for the cable passthrough hole on your desk.Scaled to fit 20mm diameter holes

This cable passthrough is specifically designed for ceiling tiles that are at least 5/8 inch thick.

Remix of Thingiverse cable passthrough. Made this one so that the top slips inside the bottom half. Also included a template that you can trace to get the exact hole size. ...Note: It is wide enough for USB cable to pass through.

Remix of Thingiverse cable passthrough. Made this one so that the top slips inside the bottom half. ... Also included a template that you can trace to get the exact hole size. Note: It is wide enough for USB cable to pass through.

... passthroughs I uploaded a simple holder for your devices and a counterweight for M10 nuts. It can be used to put some weight to the cable so it always falls down into the passthrough itself for a organized look :) Have fun and keep printin! ...

This is an insert for a cable passthrough for an office desk. It has a front slot intended for input device cables (mouse, keyboard) and a rear slot for other cables (monitor cables, cameras, speakers, etc.). The size of the top surface is 90 mm x...

This is a cable passthrough for Ceiling Tiles 5/8 in or greater in thickness. Print instructionsCategory: Parts Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 10-15

Instructions: - Drill a 20 mm hole through the wall - Choose the "long" part according to the thickness of your wall - Insert the "short" part on one side, and the long part on the other - Fasten with a 3 mm wood screw that's long enough to reach the...

Instructions:Drill a 20 mm hole through the wallChoose the "long" part according to the thickness of your wallInsert the "short" part on one side, and the long part on the otherFasten with a 3 mm wood screw that's long enough to reach the other...

2015-21 VA WRX/STi panel blank replacement to passthough the cable to a Cobb Accessport.

... tidy. ...It lets you pull the cables through, preventing them from slumping to the floor like loose clips. I designed it so you can attach two 3M double-sided adhesive strips to secure it in place. ...Typically, just one strip is enough for stability.

I wanted a good way to feed the power cable and PTFE tube into the enclosure without having a hole that lets a lot of heat out. I printed mine in ninjaflex TPU (85A) but I'd imagine anything 95A and below will work. You should be able to...

I wanted a good way to feed the power cable and PTFE tube into the enclosure without having a hole that lets a lot of heat out. I printed mine in ninjaflex TPU (85A) but I'd imagine anything 95A and below will work. You should be able to scale the X...

I modeled this so I could mount my TV up higher on the wall, but have the cables come out below to plug in different things (power, network, coax, etc).

After both the cable passthrough boxes are secured you can run your cables through the wall.The design for the cable passthrough box will fit a rectangle switch plate cover after it is installed in the wall for a clean appearance. This is my first...

I printed a part using strong aluminum alloy, thin walls, and moderate density. My settings were set to print with a high quality finish. ...I'm considering adding either one or two small openings in the design.

This is a simple passthrough that will protect your EVSE charging cable from the weight of the garage door if your EVSE is located inside of your garage and the vehicle is in the driveway. The current model will fit a cable that is up to 20mm in...

These are larger versions of the cable passthrough tube used for mounting the power supply and/or LCD controller outside of the Prusa LACK Enclosure V2. _lack_cablepassthrough provides enough room for the power cables as well as a USB cable for...

The design includes a hidden cable compartment behind the charger housing, which keeps the cable organized and out of sight. A narrow channel runs along the back of the charger to secure it in place. The Bosch charger fits snugly into its designated...

... make a difference. The holder is small enough to be printed on a 120mm bed like the Monoprice Select Mini has got and took me roughly 4,5h to print in medium Quality. You can screw it onto the wall using 3.5 - 4mm countersunk screws (~20mm length).

## Customizable Snap Assembly Cable Passthrough Grommet ### Update 12/22/20 Updated customizer (openscad) script to version 5.4, with the following changes: * Grommet diameter value now refers to the outside diameter, instead of the inner bore...