cable management rack 3d models

This simple cable management rack/box can me mixed and matched to your own sizing! All you need is at least 1 Start, 1 End, and if you decide to, 1 or more middle peices. ...These can be glued together (easier way to glue coming...

Corrected from the original, where the spacing between the hooks was too wide to my taste, though there is the original as well. I also took out most of the mounting holes that only delay and mess up the print. ... The Sketchup file is attached for...

This is an optimized version of the 19" rack cable mounts that reduces print time quite a bit (from 2h 15min to 1h 35min for all three at once) while not sacrificing stability. ... optimized for .32 layer hight, .4mm line width.

This is cable management for RACK 1U

Network cable organizer for rack. ... It fits 1 RU standard. Side mounting (optional 8mm bar for side to side cable guide). 3 buttonhole for vertical cable management with velcro strips. ...

A cable management system designed specifically for rack mounting is available in a 2U configuration. ...This organizer keeps cords neat and orderly, enhancing the appearance and functionality of your setup.

We have a lot of wire racks, often referred to as metro-shelving (check it out: https://amzn.to/3bXjF6s), and plenty of cables lying around the shop. We needed a solution to keep our cables tidy, so we designed this cable hanger that clips onto the...

We have a lot of wire racks sometimes referred to as metro-shelving (see more here: https://amzn.to/2zUXual ) around the shop as well as a LOT of cables so we designed this cable hanger as it clips to the front part of the shelf and allows to neatly...

This is a Comprehensive Cable Management System specifically designed for a Standard 1U Rack Mount Enclosure.

Networking rack cable management hook designed for a NavePoint Wall Mount Open Frame Rack, but it may fit onto other racks as well (haven't tested). Designed to be compatible with M5 hardware. ...

An innovative solution for managing cables in rack-mounted servers is an arm that holds the cables, paired with threaded rod extending several feet. This setup enables technicians to work on a server while it's fully extended from the rack without...

We don't handle a large number of cables at work, so investing in cable management systems for only a few times a year wasn't cost-effective. Additionally, I needed something tailored to my specific requirements. I wanted the ability to route power,...

Managing cables in your data center is a hard task, but this vertical organizer for racks are useful. Designed to save space, maintain airflow, and keep efficiency. ...This cable manager simplify installation and allow you to securely route cables to...

1U Cable Manager for 19" Racks

Customizable 19-Inch Rack Cable Organizer for Enhanced Management Built upon a fantastic design from mrsim0ns, our improved 1U cable manager features reinforced walls for increased durability and stability. We've also refined the mounting hole layout...

I'm fed up with the clutter of android devices on my desk and the tangled mess of charger cables everywhere, so I built this phone rack to solve the problem. The goal was to create a system that organizes both phones/tablets and cables - whether...

I built this clip specifically for use on my server rack, where it can securely hold multiple Nema cables in place. For optimal results, I highly recommend printing them with a dense infill setting. My own prints were made from PLA with a 20% infill,...

This is a replacement part for cable management panels. The panels I had did have five square holes almost 12mm × 12mm. There were plastic parts inside these holes but the plastic was ancient and crumbled while trying to use them. To fix the...

I used Tinkercad to modify an existing bracket, making it more robust for my purposes. The original design was too fragile and lacked the sturdiness I needed. ... I went straight to the source, referencing two specific models online:...

<p>I used Tinkercad to modify an existing bracket to make it more durable. The original was too flimsy for my usage.</p> <p>Here is the original. <a href="https://www.thingiverse.com/thing:1363246">https://www.thingiverse.com/thing:1363246</a></p>...

I designed this custom cable management system to fit snugly into my 19-inch rack, keeping cables neatly organized and out of the way. The zigzag gap in the design allows for effortless cable insertion without any risk of them falling out. I've...

Some easy cable management clips for a wire shelving unit. ... Accommodates 1 inch posts.

Multiple orientations become possible when this specific hole configuration is zip-tied to a server rack. The hole configuration and side screwdriver opening also allow for various surface mounting options on wood, wallboard, etc., using standard...

This is a cable management solution for rack unit installation. There are real metal products that you can buy but I want to come up with a solution using 3D printed material. This is a 2-piece part, a plate, and the hook. The hook can be inserted...

This product is specifically designed to work seamlessly with a three-tier wire shelf available exclusively at Target stores. ... To access this item, visit the official Target website at...

Cable managing clips for solar panels, antenas or roof mounted lights on the Front Runner Slimline II roof-rack. The slat they are mounted on must be disassembled as they are inserted from either end of the profile. Because the base is square...

It's been a while since i was thinking of dumping my cable panel in the basement rack. It just did not make my cabinet tidy and there was not enough space for the cables too.So i decided to make my own design which seems to work. It is quite sturdy...

Based on this fantastic Thing created by the talented mrsim0ns, I've built upon their original design with reinforced walls and subtle tweaks to the attachment points.

Rack Mounted Cable Management Clip - Kabel Management Serverschrank Kabel-Führungsbügel für Netzwerk-Schrank

Modular Rack for a docker home server - 4xPi4, 2xGS908E and cable management PLA/PLA+ M2.5 or M3 (not a perfect fit) x 10mm pan head screws/nuts to hold modules together Recommend plastic bond as the nylon screws weaken Not great but works for me -...