cable 3d printer

I designed a custom cable holder for the 3D printer's CTC printhead, ensuring the stepper motor cables are safely secured and protected from damage caused by bending or breakage. ...This solution aims to provide valuable assistance to numerous...

Follow me on YouTube http://youtu.be/nFnrcWJ5Peo http://bit.ly/2nZ0YzB & on twitter https://twitter.com/Afro3dP Printer: Kodama Trinus 3D Printer Rafts: No Supports: No Resolution: .200 Infill: 35 Notes: 2 Shells 2 bottom & Top Layers Simply print...

3D Printer Creality CR-10 Smart Pro 3D Yazıcı kablo tutucu you do not need to use support at all

CNC Mill Cable Management System: Designing a Customizable Guide from Scratch for Secure Motor and Sensor Cable Fixation A purpose-built cable guide has been engineered to secure motor cables and sensor cables on a DIY CNC mill, ensuring a safe and...

... print head. ...I made a couple of large parts that required the print to use the full x axis and after an hour the print head cable would come loose and cause the print to stop. ...So I made this clamp hold the cable header to the print head assembly.

I thickened the holes for the screws because they were breaking off too easily. PETG works well for "Snap Fit" parts and is a solid choice, but ABS should also serve you just fine. ...On the other hand, PLA tends to sag over time, so it's not my top...

A simple heat bed cable strain relief for the SOVOL SV06 3d printer. The 3D-printed piece fits around the cable and inside the existing cable cover. use a zip-tie to clamp the cable in place. Make sure to put the tie head on top so it doesn't hit the...

When using heat bed cable supports, it is important that cable movement is restricted near the solder joints, but it is also very important that the cable is not restricted in its movement by using zip ties directly on the cable. One advantage this...

This heat bed cable strain relief raises the cable up to a 30° angle coming out from the heat bed and minimizes/eliminates cable contact with the rear frame cover.The most common cause of heat bed cable failure is solder joints breaking from constant...

This simple upgrade keeps the heatbed cable from dragging on the work surface and rubbing on the plastic cover at the back of the base frame. This small upgrade also restricts the movement of the cable coming out of the control box. This is an easy...

I designed this bracket to mount on the right-side idler assembly so that the cable could be routed to the MCU board via the cable entry on the right side of the case.The plate the bracket mounts to is 3mm thick. I designed this to have a 2.5mm wide...

Lock Secures Patio Umbrella in Place When Tilted to Block Sun. Designed Specifically for 37mm Diameter Umbrella Poles, but Also Compatible with Sizes Ranging from 36-38mm, Though Extensive Testing Has Not Been Conducted. If You Find This...

For keeping the workspace tidy by organizing cables.\r\n\r\nTo view my other projects, please visit:\r\n\r\nDamper Foot For 3D Printer\r\nhttps://www.thingiverse.com/thing:4005655\r\n\r\nTurning Buttons For 3D...

--------------------------------------------------------------------------------------------------------------------------------------------------------------- Snapmaker2.0 A150/A250/A350 3D-Printer Heater Bed Plate Cable Holder This power cable...

... another part to secure the other side of the cable on the 2020 extrusion. This setup is specifically designed for my HyperCube 3D printer build and can be sourced from Thingiverse, as referenced by the URL http://www.thingiverse.com/thing:2111707.

This is a scaled down version with a lower profile (15mm bend radius) that fits neatly and completely under the Prusa i3 heatbed. Outside measurements are 19mm wide X 10mm high. inside measurements are 9.5mm wide X 6.5mm high. Lower profile was...

This is Version 3.0 of the Enhanced Cable Management for Zonestar P802Q 3D Printer Utilize a 4mm nylon filament to add strength and prevent cable bending Print Settings Printer: Zonestar P802Qs Rafts: No Supports: No Resolution: 0.2mm Infill: 25%

Clip on wire management for Cr-10 / any printers with a 20mm x 20mm extrusion. I also allowed a concave in the middle at the back to account for any T-molding so it will still sit flat. Pro Tip. The clips are rigid initially. Put a screwdriver...

Clip on wire management for Cr-10 / any printers with a 20mm x 20mm extrusion. I also allowed a concave in the middle at the back to account for any T-molding so it will still sit flat. Pro Tip. The clips are rigid initially. Put a screwdriver...

Customized version of http://www.thingiverse.com/thing:1232747 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1232747 Instructions Using the following settings: Radius Chamfer = 1.0 Diameter Distance = 13 Width...

Created with Customizer! ... Using the following options: W_cube = 25 Text = TECH FORCE L_cube = 10 H_Bottom = 3.5 R_Chamf = 2.5 D_screw = 1.5 txt_size = 3.0 txt_height = 1.4 H_head = 6 cutaway = 100 text_mode = 0

I used anubis86's "Soft Bowden Filament Guide without Cable Holder" as my template... then I thought to myself... "I want that cable securely in place!!!" So, I modified it... and I uploaded both versions... so you can print them too... ... This one...

I was seeking an uncomplicated way to identify the cables of my OX CNC machine. To accomplish this task, I created these straightforward labels and designated the letters X, Y, Z, and A for them. ... To secure each label onto the cable, simply use a zip...

The cable guide works with other Creality 3D Printers as well. ... **Bill of Materials** - M3 Threaded Inserts (6x) - https://geni.us/ThreadedInserts - M3 Round Head Screws & Hex Nuts (various lengths) - https://geni.us/M3-Screws - 3x7x3 mm Ball...

You can learn all the details by watching the YouTube video. ... The parts must be printed without any support, the design is made that way, place the parts as seen in the photo, you do not need support Considering that the screw is plastic, it must be...

Visit Thingiverse Apps to Learn More: http://www.thingiverse.com/apps/customizer/run?thing_id=58091 Instructions Using the Following Options: Printer Label Settings PRINTER: Label Settings for Your 3D Printer Thickness: 1.2 mm - Perfect for a Variety...

This is a simple guard to put on the top frame of a printer so a cable draped over the top will not rub on the sharp corners of the 2020 extrusion. 9/2/20: Uploaded version 2. Now with push-on fit and with side stops. ...Print Settings Supports: Yes...

This cable chain provides a straightforward yet effective way to safeguard printer wires.

The cable protection for your Solidoodle printer is straightforward to set up and install, making the process a breeze!

VGA cable guide for Tenlog dual extruder printers. ...Two M4 16mm screw and M4 T nut hold each to the top of frame