c3 corvette radio upgrade 3d models

The orientation is just right, so you shouldn't need to change it.After printing, the lid is placed in the box with the bump facing inside the box at the end where you thread the lid like this: If you do not want to install / fiddle around with...

Human: MK3(S) Compatible X-Carriage compatible with the Bondtech Prusa Extruder (https://www.bondtech.se/en/product-category/upgrade-kits/prusa/) and the Revised X-axis (https://www.thingiverse.com/thing:3559732) --- Compatible ONLY with the Revised...

If you modify or upgrade any parts (feel free) just link them back to here. Updates – None. So, this is the - Battery. Problem I had was balance on the plane, needed a lot of weight forward so there are two battery holders. Moving the battery...

I upgraded to an E3D V6 and made this mount and part cooling duct for it. I've been using this design for several months now. The only thing that is relatively new is my using of printed bushings and the bushing holders I made. The part cooling duct...

These are upgrade parts for DJI F450 arms we all know and love. You can use any length of carbon tube you want provided they have 16mm OD and 14mm ID. Also, you need to drill a hole at one end of the tube. Use the motor mount itself as a drill guide....

It should be fully rules complaint but check dimensions before using this design.Note: At time of upload, the design has not been tested in competition and has no guarantee of performance.Note: The pictures included with this design show a Launcher...

Due to the side mounted design, the results are better IMHO than other direct drive upgrade kits I have previously purchased. However, the increased weight of the direct drive assembly does cause some minor artefacts to the surface quality in...

Description I designed very rigid and simplistic direct drive mount for my TwoTrees Bluer V2. I haven't found a solution that fits V6 hotend and have proper 5015 part-cooling fan. My main goal was to use a minimal number of external parts and keep...

size is 100x50mm and 100x100mm and works with "Yet another floor tile pack" https://www.thingiverse.com/thing:3895156 - Yet another floor tiles pack ________________________ If you like my work please consider supporting me on Patreon. Become a...

Many of you will never find / have found these parts on Thingiverse, but since I think this upgrade makes a lot of sense I uploaded it here for you.These Z-motor mounts are openable which simplifies the removal of the entire X-axis and the Z-spindles...

I know a lot of MMU2S are in the box, give it another opportunity.Use the PRUSA stock firmware.You can find the assembly guide here: (Translation in progress, if you use Chrome right click and translate the...

I have spent the last 2 weeks upgrading my printer and tweaking the firmware and slicer settings to get the best possible finish using silk copper filament. The stuff is so shinny, any defects in quality are very visible. I hope to me printing...

To use the "duplicate" function, you need to have the free DesModder Chrome extension installed.Also see my ARITH-PAD for an upgraded num-pad.READ THESE NOTES:Everything prints without supports! It is possible the files will import into the slicing...

 It will be like a custom piece of art that filters the air in any space you need!!! I may add some storage or wall mounts to the design at a later date.  SO NOW TO THE FUN PART!!PARTS: ACTIVED CARBON PREFILTER Amazon.com: Universal Cut to Fit Carbon...

Try to press them partway into the hole in the print, then place them in a vice to evenly press them the rest of the way into the hole.FutureActive CoolingWith the LEDs on for a potentially long time, I would like to upgrade from passive to active...

It uses the same rails as the original design, so you can reuse the rails if you decide to upgrade to the full design later on. Note: There are now two plugs available: Locking Plug: original plug, locks in place, but difficult to remove. ...

It will stay on the second layer until you press it again, or if you used the “Confirm” tool.Also see my ARITH-PAD for an upgraded num-pad.READ THESE NOTES:Everything prints without supports! It is possible the files will import into the slicing...

Even sitting right next to the printer, the sound produced is very low, pretty-much drowned out by my noisy fans (that's the next upgrade)." "Easy to installed and shocked at how much they cut down on the noise!" SQUASH FEET... Derived from an...

I designed everything about a year ago but hadn't uploaded any of the files because I upgraded some of my game componants and didn't think there were many others who had done so. I've broken out the description for each piece so you can print what...

This is an upgraded version of the num-pad that has left and right arrows, delete, and equal &nbsp;sign! It works on a computer or iPhone!</p><p>Press and hold any key to repeat quickly.</p><p>Also see my <a...

We've used Intelligrill hundreds of times since it was born with great results, but unfortunately, after years of problem-free iOS upgrades on our iPhone and iPad devices, the App Store announced that the newest release of iOS would break my iOS...

This design allows an inexpensive and easy upgrade from the stock extruder on the Elegoo Neptune printers to a Voron ‘M4’ Mobius extruder. <a...

Unfortunately, this addition defeats the quick nozzle change feature of the original fan mount design.\nBy the way, if you haven't upgraded your heater cartridge to 35W, I highly recommend it. Completely eliminates the temp error, even with thick...

I wanted to upgrade my Replicator 2 with a Super Mario inspired theme! Aside from the blue paint used on the panels, every single piece was 3D printed and not painted or finished in any way, the multiple colors are due to swapping filament colors...

________________________ Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool https://www.thingiverse.com/thing:4654396 - Rivet Placement Tool https://www.thingiverse.com/thing:4165457 - Smoke Stack Addon for...

FORMAT Supported formats encompass FBX as a top-level format which is safe to employ on backwards compatible software version such as 3ds Max starting with edition dated back to Year:2017 up until at least year-2020 inclusive of any minor point...

*"Main-Small Token Tray 1x2.stl" |"Main-Small Token Tray 1x3.stl" |"Main-Small Token Tray 2x2.stl" - x3 - Print whatever combination of 3 makes sense to you, I printed one of each *"Main-Token Tray.stl" - x1 - Holds the round terrain tokens and is...

You can find this here: https://www.thingiverse.com/thing:3883602 (NEW UPDATE 9/2019 - Metal Shafts on Gear Carrier with Bushings) I built a Rover 2.0 and incorporated the changes made by escexed in his "Planetary Gearbox Upgrade for FPV-Rover V2.0"...

You can use as many or as little of these Upgrades as you like. ---------------------------------- You will be required to download the simple Stand from https://www.thingiverse.com/thing:4295280 and if you want the ammo box then its from...

I need to upgrade to a Volcano for bigger items (LOL). You will need to modify the source code for this project. It is 99.99% complete, all you need to do is enter the wifi SSID, password and the authentication code for Blynk and recompile and upload...