c270 mount 3d models

I drew inspiration from https://www.thingiverse.com/thing:2916010 and incorporated the bracket mount from https://www.thingiverse.com/thing:2828913 into my design.\r\n\r\nI don't own a CR10, nor have I tested this, so if it doesn't work out as...

I found this mount and thought it was great until I realized the camera was practically touching the heating element and that was before I added the thick focus wheel (thing:714475) that is required if I want to be able to see what's going on...

Remove the monitor bracket from the camera, the mount then fits in place of the monitor bracket. Note the camera is mounted upside down, this is to allow the camera to be situated slightly to the left on the gantry and therefore miss the Z chain but...

I required a camera mount for a project so I repurposed an existing design. ...The end result is not the most user-friendly configuration, particularly considering that the vents are now positioned at the base, but it meets my requirements and gets the...

I needed a simple replacement for the original mount on my Logitech C170. To remove it, I ran a hacksaw between the gap at the camera end and the blanking plate. Then, I used a round magnet from B&Q to secure it in place. ...If you ask politely, the...

... but unfortunately, it also introduced grainy footage due to the increased movement. Although the springs offered some improvement, I decided to switch to a wall mount with a swing arm design, which ultimately resulted in much less vibration overall.

Remove the monitor bracket from the camera, the mount then fits in place of the monitor bracket. Note the camera is mounted upside down, this is to allow the camera to be situated slightly to the left on the gantry and therefore miss the Z chain...

you can easily remove the original mount by running a hacksaw between the gap at the camera end at the end with the blanking plate. ...I have used a round magnet that is used to hang prices from a well known high street diy shop (B&Q) :-p If you ask...

Designed up this webcam mount to use in my Creality enclosure so I could view my prints through Octoprint. It was inspired by Red44123's design. The problem I had with their design was that the webcam's base needed to be taken apart, and that...

UPDATE 2019/08/04: Today I snapped my camera mount while tilting the printer, forgetting about attached parts that might stick out :-(. In case you've experienced something similar here it comes - the reinforced version! I hope that the modified...

Wasn't showing up on my profile for some reason on thingiverse. Designed up this webcam mount to use in my Creality enclosure so I could view my prints through Octoprint. It was inspired by Red44123's design. The problem I had with their design was...

This is the mounting arm I designed to pair perfectly with the C270 camera mount (https://www.thingiverse.com/thing:2816919). Created using Crystal Series PETG - Yellow from Maker Geeks, this design showcases exceptional strength and lightness due to...

Remixed this ender organizer to add a Logitech c270 mount for my octopi to stream from. looks weird, but hey, this is my first upload. ...lmk what you think .

I created a Logitech C270 mount that connects with a GoPro stand-off mount, specifically designed to work seamlessly with RepetierServer connections when I was searching for a flexible mounting solution for my Flsun QQ-S Pro. ...This setup can be just...

These webcam arms are just two longer versions of the Logitech C270 mount by BKMorpheus (great design by the way). ...I needed more length because my webcam was too close to the bed on my Kossel Linear Plus, so I lengthened the arm and camera...

This is a rework of the Logitech C270 Mount for the Prusa i3 MK3/MK3S, https://www.thingiverse.com/thing:3272618 by SethBon. I added a snap-in holder for the IKEA LED lamp "Jansjö",...

These webcam arms are essentially longer versions of the Logitech C270 mount designed by BKMorpheus, a truly great designer. I needed to extend them because my webcam was too close to the bed on my Kossel Linear Plus, so I lengthened both the arm and...

I used tree supports under the camera mount bit :) I used this model for the C270 Focus ring, no need for the mount as its for the prusa; https://www.printables.com/model/235784-prusa-mk3s-logitech-c270-camera-mount-focus-ring-kI also got a smart...

 Bit of a mash up I was already using the X-axis cable strain relief clip, so I incorporated geektoybox’s C270 webcam mount.  Perfect for spaghetti detective or general nozzle/print checking. Added an extra 10mm offset towards the...

The C270 Webcam Mount is specifically designed to be used with the CR-10 X-Axis Belt Tensioner, a device that helps to fine-tune the belt tension on your 3D printer's X-axis. This mount allows for easy installation and secure placement of the webcam,...

This is a remix I made of a C270 webcam mount for the ender 3 V2I lowered the webcam down to give clearance for a CR Touch. This position gives a better view of the print to check for spaghetti but less of a “top down” overview.</p><p>This model...

This is a remix I made of a C270 webcam mount for the ender 3 V2I lowered the webcam down to give clearance for a CR Touch. This position gives a better view of the print to check for spaghetti but less of a “top down” overview.This model isn't easy...

That part is reused from https://www.printables.com/model/187968-creality-cr-10-smart-pro-camera-holder.Then attach your C270 as described here: https://www.printables.com/model/3991-logitech-c270-mount-prusa-i3-mk3And you are good to go!Two versions...

Adjustable mounting arm for C270 camera. Mounts to the x axis limit switch cover using existing holes. I removed 2 of the motor mount machine screws and drill and tap the mount for M4s. Two M3s is plenty of holding power for the x stepper motor , so...

Remixed for single-part printing with Logitech C270 webcam mounted on Monoprice Select Mini. The C270 is an affordable and reliable option that works seamlessly with Octoprint. This mount cleverly reuses the plastic pin and existing screw that comes...

Ball mount (1" / 25mm) adapter for Logitech C270

This is a mount for the logitech C270 camera to the post of a lack enclosure.

As I have lot of different go pro mounts, wanted an easy way of mounting c270 camera to printer

Simple and easy to print wall mount for the Logitech C270 camera I'm using for Octoprint.

I set out to remix IgorF2's ingenious articulating lamp, but this time with a purpose in mind - creating a sturdy mount for my trusty Logitech C270 camera.