c mount 3d models

The DXL Hyper C Quadcopter frame requires a 30-degree GoPro session mount. A square of adhesive rubber foam is ideal for preventing slips, but only when applied properly. To achieve optimal results, print this mount on its side so that the strap hole...

A simple cap for the male end of a C or CS mount lens. You may need to scale up or down by 1%. ...Default fits my wide angle macro lens fine, but it was slightly to snug for different lens so I had to scale it up in the slicer.

My solution involves mounting Part A to the back plate, then securing it to the carriage. This allows you to attach Part B to Part A with ease. However, this design does obstruct the "quick" removal of the back plate. Nevertheless, I believe removing...

The C clip should be printed with the clip part flat on the bed for maximum strength. It can be installed onto one of the end brackets at the end with 2 hex bolts and wing nuts. You'll need to print 2 large knobs and 1 small knob. There is an...

Make sure to do this on a flat surface to avoid making the rails crooked. The C clip should be printed with the clip part flat on the bed for maximum strength. It can be installed onto one of the end brackets at the end with 2 hex bolts and wing...

Raspberry Pi Camera Housing featuring a CS (C) Type Lens Mount

Based off of the TETRIX MAX Inside C Connector, this mount for the REV Core Hex Motor empowers versatile mounting options along a TETRIX Channel. Originally designed for a drivetrain concept that got scrapped, this part proves useful anywhere a Core...

... for Hayear HY1139 camera not getting focus along with the microscope itself. ...Adapter rises the mount about 10mm and resolves the issue. The top hole for the camera is a tight fit, the bottom part can be rotated to adjust camera position. ...

Adapter ring to mount SVBony 305 CMOS camera on 9x50 Celestron scopefinder. Print at the highest accuracy for good result. May need some fine filing after printing. ... Depending on material used it should be printed at a scale bigger than 100%...

combination of https://www.thingiverse.com/thing:83754/files and https://www.thingiverse.com/thing:4560254/files

Printed without support. ...PETG / layer 0.1 / perimeter 4x.

This is a camera enclosure/lens adapter for Raspberry Pi. The holder links are taken from: https://www.thingiverse.com/thing:2875976 Printing recommendations: I print this on PLA, 3 perimeters and 20% infill with a 0.4 nozzle at 0.2 layer. Only...

Fits to the USB Webcam. ... https://www.thingiverse.com/thing:5909063

Adapter to use SV305 cmos sensor with any Nikon F Lens Print at highest precision possible. Some filing could be required depending on the print quality. ... Compensate for material shrinking by adjusting scaling percentages (101% in my case with PLA)...

Fits to the USB Webcam. ... https://www.thingiverse.com/thing:5909063

the power of sight

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/96FlwO5Rv96

Raspberry Pi users can now attach the M12 lens adapter to their HQ Camera, which features a C-Mount design.

File explanation:CMountToM39Extension-A-Bottom-Length44mm: Fits into a camera C-mount (1-32 UN 2A thread), allowing for any of the top extensions below to be attached. 44mm in length.CMountToM39Extension-B-Bottom-Length24mm.stl: Fits into a camera...

This is a versatile C-Mount adapter for a high-definition USB camera module from ELP, available at http://www.elpcctv.com/mi5100-5mp-usb-camera-module-usb20-aptina-125inch-color-cmos-sensor-100degree-lens-p-221.html To use this adapter, you must...

Adapter consists of two pieces: -adapter with C-mount screw -adapter to T2 screw (M42x0.75) As I was not sure about the flange focal distance of the lens (whichI found on ebay), the two pieces can slide axialy. There is a gap of 0.2mm between both...

This is an adapter to position anything with a c-mount, such as the raspberry pi HQ camera, on the trinocular part of the Olympus CX33 microscope. Print in black for proper color balance. Twist to adjust to a proper height. ...Use an m3 or m4 to lock...

Meant for low cost 50mm F1.4 C mount lenses with 39mm OD. this will cut the aperture to 26mm (F1.9) 1.25" Filter is securely held in threaded tray. Tray has side access to allow grabbing the filter, without risk of touching the optical...

Me neither, so I made this adapter that bolts to the camera instead of the stock C-mount and replaces the part in the FirstScope focus mechanism that has the set screws to retain the eyepieces. Result is that the camera screws directly into the focus...

Me neither, so I made this adapter that bolts to the camera instead of the stock C-mount and replaces the part in the FirstScope focus mechanism that has the set screws to retain the eyepieces. Result is that the camera screws directly into the focus...

A precision light shroud designed for 8-50mm f1.5 3MP IR C-mount lenses is at your fingertips. The included angle of the cone measures a generous 42 degrees, ensuring that even the lowest zoom setting on a 1/3-inch sensor will be adequately...

Version 2.0 of https://www.thingiverse.com/thing:4880071 Adapter consists of two pieces: -adapter with C-mount screw -adapter to M42 screw (M42x1) -adapter to T2 screw (M42x0.75) As I was not sure about the flange focal distance of the lens (whichI...

Like [the Original](https://www.thingiverse.com/thing:4364692), this Thing is designed to house Nikon lenses on C-mount cameras, e.g. the Raspberry Pi HQ camera. This remix increases the field of view and the minimum focusing distance in...

I mounted the Xfinity XiD-C to the back of my TV by whipping up a quick solution that I'm excited to share with you. Print it out as instructed, and you won't need any supports at all. ...To secure it in place, I used removable double-stick tape that's...