bushnell trs 25 lens cover 3d models

Some cover for Bushnell TRS-25 collimator also you will need: - M4 bolt + M4 nut - 2 pcs - M3 bolt + M3 nut - 2 pcs, one nut will have to be sharpened with a file - heat-shrink tube for M4 bolts - 2 pcs - thread-locking fluid if your nuts are not...

Our TRS-25 came with the lens protruding from the body (a manufacturing defect that we didn't notice until after the warranty expired. Bushnell was absolutely no help). ...The sight works as advertised, so I made this extender to keep the lens cap from...

I used "SGT KNOTS Diamond Grip Elastic Bungee Cord - 100% Stretch and Shock Absorbent for Camping, Kayak Deck, Crafting (3/32" x 10ft, Black)" from Amazon to connect the lens covers together. ...I'm sure any shock cord with 3/32" diameter will also...

I used "SGT KNOTS Diamond Grip Elastic Bungee Cord - 100% Stretch and Shock Absorbent for Camping, Kayak Deck, Crafting (3/32" x 10ft, Black)" from Amazon to connect the lens covers together. ...I'm sure any shock cord with 3/32" diameter will also...

Non spring loaded flip covers designed to work with Bushnell TRS-26 red dots. The hole on the Lens Cover parts may need to be slightly filed to allow a roll pin to fit, although you may be able to just hammer one in. The holes should be able to fit a...

Bushnell TRS-25 Red Dot Sight protective covering ring

Protection lenses Bushnell TRS-25 allow for the transport of two Lithium CR 2032 batteries. ... - Printed in Black TPU.

... des orifices pour installer un élastique de maintien. Le fichier SolidWorks est fourni. Here are protective covers for a Bushell TRS-25 red dot. The inside diameter is 28 mm. There are holes to install a rubber band. ...SolidWorks file is provided.

to fit the large and small ends, respectively, of a set of vintage Bushnell binoculars where I had found the original plastic ones to have cracked due to age.The company logo is inscribed on the outside using their vintage logo which I painstakingly...

The main task at hand is creating a bushing that snugly covers the aperture of a Bushnell Northstar 4.5 inch telescope. ...To ensure an adequate seal, we aim for an inner diameter just slightly below 50 millimeters - close enough to provide a solid fit...

Printed this for my Bushnell 850 disc golf range finder. It may fit other Bushnell models but that's the only one I've tested. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/aa4tjUu4EfG

This is a protective cover for a Bushnell Pro X2 Rangefinder...i use this constantly when golfing and hate taking it in and out of its zippered case so i made a quick cover to protect the front elements Can be printed in any filament...PLA holds it...

With the digital Equinox Z Night Vision monoculars from Bushnell, you’ll be able to enjoy outstanding optical clarity, ultimate illumination and an unmatched field of view. ...Features such as zoom, image capture, video recording and daytime color lead...

Bushnell PowerView 10x50 replacement lens caps are available for purchase.

A 2.5 power reading glasses lens is great for 12"-18" shot. ...Personal use only.</p>

Experimental top cover. ...Have a 60 mechanical keyboard and a wide format LCD panel, to stuff in a TRS-80 model 100, without destroying the precious.

Replacement rear cover for a TRS-80 Model 16B, with openings for two 120mm fans. Newer version flattens out the bottom bevel (on the outside) for a cleaner print and corrects thumscrew positions. ...

TRS ON-E kids trails bike shock cover replacement. The original one does not protect the suspension elements from dirt and water, this does a better job. ...Print in PETG or hard TPU, no infill, resolution 0.3 should do.

This is a replacement cover for the System Bus / Option ROM compartment. It was the prototype for the other covers I designed. ...

I decided to create this cover after one day noticing that there used to be a cover there. So, here is a cover to make your pocket computer more complete. This end cover is for the model PC-2 Pocket Computer and will most likely not fit on the PC-1...

Battery cover for the Tandy 100: It's a precise fit because I designed it to print in PLA with extra plastic at all stress points to prevent breakage under normal use. If that's okay with you, you can print a replacement battery door yourself. Print...

A protective cover for the Bushnell RXS100 Red Dot Reflex Sight. I lost the original cover that came with it, so I made this. ... The parametric version is customizable in SolidWorks, if it fits too tight (or too loose), or you want to change the...

This is a TRS-80 drive face for my 5.25" RPi drive tray. It just glues on so, you can use it for ANY 5.25" tray. ... The face is slightly wider than the tray so when you glue it, make sure you center it.

A lens cover for Microsoft Lifecam with frictionfit

Creating a Lens Cover for the MY4777 Class Utilizing FreeCAD as a Design Tool. ... The Original File Can Be Found at: https://www.youmagine.com/designs/lens-cover-design

Easy Shield Lens Cap

I needed a new lens cover for my laser range finder because the old one was worn out and did not stay put anymore. ...Therefore I have created this one as a parametric design in openscad so that it can be adapted to other lens diameters aswell. The 3D...

First out are the preliminary models of a lens cover specifically designed for our brand-new EOS 70D cameras. ...The initial test units provide a much-needed minimal protection during daily use and transportation, making them highly valuable additions...

Using the Following Options: Interior Height: 40 mm Hinge Thickness: 0.3 mm Rim Inset: 0.6 mm Interior Length: 10 cm Lid Inset Height: 1.2 cm Lid Inset Offset: 0 mm Hinge Width: 12 mm Hinge Length Scale: 110% Tab Size: 1 mm Side Wall Width: 11 mm...

This is a slot cover for the Mega Mini MPI used by the TRS-80 Color Computer. Revision 2 is slightly smaller and removes the text, which was difficult to print well. ...