bunny ears 3d model

The estimated date of completion is not yet known, however, since I am in my final GCSE year and have more pressing work to attend to, you could expect at least another month before even a partially functional complete model has been released. I...

There is also a reverse mount for the hygrometer that's for mounting it on the inside of glass (also fits stock model).The hygrometer has an extender for the button that switches between C\F. You will need the original rubber insert...

They are both definitely WIP, I do not own a Orbiter V2 and are based on the CAD models. Update:18\10\21 Uploaded some 5010 fan ducts which are 8.5mm longer to allow for a Volcano Hot End. These are definitely WIP. I have not printed, installed or...

Originally designed for the Ender 3-V2 model, reusing the 4011mm Original axial Fan as Nozzle cooling. The original fan is loud, you will probably wish to change it with a quieter one and higher performance 4020 axial fan! Many options are available....

One suggestion offered is to quickly wave fire under the problem area in the hopes that the hair will burn away before the plastic is damage, but I came up with a different solution.This set of models replaces the entire front wheel assembly. The...

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers). For adjustable friction, I've added a simple bail that attaches...

... Very basic stress testing was done in Fusion360 with a model of a 1.5" PVC pipe sleeved over the mount and it seems like it won't snap too easily. ...In real life testing, it holds a ~7lb antenna easily.</p> </p></div></p></p></p> Category: DIY

Really like the wheel from TheSloppyApprentice's Watermill and was looking for ways to hold it besides that large frame in the source.So I could make it stand in a bassin or hang under some opening where water is dropping off.So here are 2...

So far my failures are in optimizing the printer tuning to keep the model airtight. As stated in the Harvard paper, they printed a form and molded silicone for the soft actuators. I probably should do that too, but I am determined to work with FDM...

The left adapter does require a small alteration which I did with a pair of side cutters (the ones that came with my Ender 3) (see pictures): - Unscrew the four screws at the bottom (be careful these strip easily) - Gently pull back the white tabs...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be omitted on the inside. These connectors are specifically designed...

  I've been using the one in the picture for a few weeks and apart from not looking as pretty with the cam open, there's absolutely no difference in performance.I think I have allowed enough room to print this model with a .6mm nozzle but if you are...

The COMPLETE Swamp Gurunda bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Swamp Gurunda (Presupported) The amphibious people of the swamps, with slimy skin and innate...

Enjoy my Ulvheim Small Merchant House. It came from my Patreon February Release. Thanks to all my supporters and to Markus Kruse / Terrain4Print, creator of the Ulvheim City. This model is supportless as usual. :)</p> <p>Discover my Ulvheim Remixes...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

Use for reference) Hardware needed: Two 5015 blowers (get the correct voltage for your printer model). I recommend Sunon maglev. Europe: https://www.tme.eu/gb/details/mf50151vx-a99/dc12v-fans/sunon/mf50151vx-b00u-a99/. A suitable connector to the...

It was just hard to get some of the screws in it so I had to manually remove the parts this model has removed for you. Make sure is you use screws to hold the bearings tight that the lowest ones have low profile heads or they will be lower than the...

Keep doing it until you get a reliable contact. Multi-color printing For printing in multiple colors, you need to slice the model and save it as normal gcode. Then, you have to insert the M600 command. You can do this manually by opening the gcode,...

IMPORTANT INFO REGARDING ARRMA 6s REAR HUBS: There are basically two versions of the Arrma 6s rear hub between all the 6s models (36mm wide and 45mm wide). <b>The recommended version are the hub parts used in the 6s Kraton/Notorious/Outcast which...

Now, everything will just fit without removing the box insert.ModelQtyDescriptionquacks-chip-box.stl2Boxes for Red, Green, Blue, and Yellow ingredientsquacks-chip-lid.stl2Lids for those boxesquacks-misc-box.stl1Box for the miscellaneous ingredients...

Click the “like” button and show your support. If you find this model useful, feel free to buy me a coffee. Here's my attempt at replicating the Infinity Orb from the film Guardians of the Galaxy.In one of the pictures, you can see a side by side...

1x set of speakers from MacBook Pro model number A1226, A1211 or A1260. 3W Bluetooth amplifier module TE657 This module goes by many names, so compare pictures when you're unsure.ebay.com / banggood.com / google LiPo charger module TE585 a.k.a...

As of 09/16/2018, I've not yet modeled or printed the capstan bearings, nor have I fully solved how I will drive the capstan. My current thought is to use a drill attached to the underside of the platform, using a belt to drive the capstan. I would...

READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?A modular tripod/handle...

Not suitable for heated chamber!Below are the temperature results of what I tried************************************************************************************* Notes:The Top_Rods_Cap.stl have a groove preventing 180° rotated insertion (they...

The water pipe has an improved shape that looks way better after being printed than the last model. Inner pot V2: made the border higher so there is more colour. SCROLL DOWN FOR DETAILED INSTRUCTIONS WITH PICTURES ! When using this flowerpot it's...

&nbsp;Obsolete models are deleted and replaced with the latest version. &nbsp;Post feedback so we can improve and keep these collector replicas running!</p><p>Change Notes</p><ul><li>4/5/22, Version 6: Best version yet. &nbsp;Dimensions tweaked for...

I have the model assembled if anyone is interested; just can't upload a .step file (check the comments for it now). Keep in mind that you may need a shim (flat washer) to fix any misalignment issues with the Creality Heatsink. I've used this...

The casing has a channel modeled in the side to accommodate the ribbon cable coming out from the Raspberry Pi. 3) Insert the smaller end of the ribbon cable into the Raspberry Pi Camera Module, then place the module into the view port. The view port...