bullseye fan duct ender 3 3d models

Just a simple fan duct I designed to funnel air from outside my enclosure to the main board. ...RECOMMEND YOU PRINT WITH WATER SOLUBLE SUPPORTS.Can be shortened for normal use.

... to enclose the upper fan, providing extra support in case the fit is not perfectly snug. Finally, an adapter has been incorporated to accommodate 40x40x20 part cooling fans, allowing for flexibility with fan ducts or direct replacement if desired.

Ender 3 Bottom Fan Cover - Laser Cut Alternative Feeling left out? Not the laser! It's now teaming up with your 3D printer, saving a ton of print time and keeping plastic debris from clogging your fan. This upgrade is quick and easy to install. The...

To address this issue, I merged Filboyt's fan duct ring with nghtshd's duct to create an additional nozzle that slides effortlessly into the Fan Mount. Unfortunately, Filboyt's original duct didn't mesh well with my stock fan, so I opted for a 5015...

I couldn’t find a good model of a replacement for the stock fan duct on the ender 3V2 so I decided to make one myself. It took about 6 iterations to get the fit right along with the built in supports being perfect with minimal material and post work....

... printed with supports. You'll also have to solder the wires to the existing fan wiring after removing the stock cover and fans. I modelled this in Fusion 360. Source files are included if someone wants to add or improve the desgin. ... Thanks.

Duto de ventilação para fonte ender 3, cole com fita dupla face em cima da ventoinha, engate um cano para capturar ar frio. ...Ideal para fechar a ender 3 sem precisar retirar a fonte do lugar original.

I recently bought an Ender 3 v2 printer as a second printer and did not plan to do any medications. Unfortunately, the cooling performance when printing PLA was less than optimal. This might be something specific to my printer. I decided to design a...

I recently bought an Ender 3 v2 printer as a second printer and did not plan to do any medications. Unfortunately, the cooling performance when printing PLA was less than optimal. This might be something specific to my printer. I decided to design...

This fan shroud bolts on to the Sprite hotend on the Ender 3 S1, with no other modifications necessary. I evaluated this cooler for cooling performance and it performed very well compared to the stock setup. Check out the [Installation...

I’m 14 years old and I made my own fan duct because I just found all the other’s to big and heavy or just ugly on the printer so i made the KAHIKU and wanted to share it with poeple so it could be use by you and improve for specific fan or...

WIP Had issues with overhangs, not being printed nicely at the back of the models, so I wanted to try with circular fan duct. Couldn't find one, built one on my own. I printed it vertically, using tree support, build plate only. ...I also used brim...

This is a remix of my own design, this attaches right under the previous mount for the fan, but you're going to need the M3 bolts to be a bit longer than the previous ones. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: ...

A remix of the SATSANA Ender 3 Remix for Micro - Swiss Direct Drive + BLtouch. ...The BLtouch was mover 3.8 mm to the left so the connector can be placed from the inside

Definitely better than the stock fan duct. I would like to make the air blow a bit more under the nozzle since right now I think it's a bit far, but still, works nice. Results I did find noticeable improvements in overhangs, doing a 70º overhang...

Definitely better than the stock fan duct. I'd like to make the air blow a bit more under the nozzle since right now I think it's a bit far, but still works nice. # Results I found noticeable improvements in overhangs - doing a 70º overhang test...

I designed and manufactured this part specifically to enhance airflow with a Creality Ender 3 printer, utilizing a high-quality Fillamentum ASA Extrafill filament that boasts superior heat resistance compared to standard PLA material.

I required a fan duct that extended down to where my nozzle landed after my Microswiss upgrade. After testing six different models, none fit perfectly, so I decided to create one myself. I'm satisfied with the stock carriage and wanted to maintain...

I made some investigations and experiments and found that the stock fan duct has a little bit deviated blowing direction. And I made an improved design that can significantly decrease the stringing. ...Please print with ABS or PETG to avoid thermal...

I made some investigations and experiments and found that the stock fan duct has a little bit deviated blowing direction. And I made an improved design that can significantly decrease the stringing. ...Please print with ABS or PETG to avoid thermal...

I made some investigations and experiments and found that the stock fan duct has a little bit deviated blowing direction. And I made an improved design that can significantly decrease the stringing. Please print with ABS or PETG to avoid thermal...

... The cable for the nozzle fan is stretched to max. First looks like it's not long enough but falls into place while assembly. Hardware 2x M3x20 & 2x M3 Nuts needed The orange 4020er fan part on the left: https://www.thingiverse.com/thing:5845783

It's a slightly redesigned air duct that features elongated mounting pad for 3 strips of 10mm LED tape - https://pl.aliexpress.com/item/1005001681576572.html?spm=a2g0o.order_list.order_list_main.20.36561c24wW8A3o&gatewayAdapt=glo2polthis tape in my...

Just tried to remix it for one 5015 blower fan.

also filled some grooves inside the duct cause they were causing thin wall conditions Used the MS 3d builder so it doesnt look clean but it does the job I printed it at 45deg, with no inside supports to minimize bridging, looks like it would also...

Remix of Creality Stock 5015 Adapter V2: Rotated the fan intake away from the x-axis rail. Now the fan won't hit the belt tensioner screw. ...

Nozzle replacement that will fit after relocating parts cooling fan to side.

Simple 90 deg fan shroud for Ender3 an Ender5 - only with the old creality-fan-housing. Comes on to the fan with some glue, you will need longer M2 screws (20mm) to screw the 4020 blower on. Fits the microswiss hotend and remakes best. ...Use some...

I didn't want to replace the original fan mount so I built one that would fit a 5015 fan. I didn't want to replace the original fan mount so I built one that would fit a 5015 fan. I'm attaching the fusion file for any personal modifications. ...For the...

I took over the project from x4runnerGunnerx : https://www.thingiverse.com/thing:4623647 I added the dragon Ender logo I hope you enjoy