bullseye bubble level 3d models

... BLTouch holder. This stops the screw head going further than needed. I use a 4020 fan so I have used the following from 0mbr4: https://www.thingiverse.com/thing:4782085 Any of the Bullseye/Blockhead dual fan ducts should work with this design. ...

Use this for mounting your Bullseye LNB to a tripod-style mount. I use this for my <a href="https://github.com/Othernet-Project/Dreamcatcher">Dreamcatcher</a> station where I don't need a full dish, just the LNB pointed straight to the satellite. The...

The petsfang works a bit better but it is actually the bullseye duct that shines with this nozzle. I therefore created this base which is compatible with the Ender 5 for direct drive and bowden setups as well as the Ender 3 for bowden setups. I use...

So, I drew up this visor (angled slightly toward the nozzle) for the bullseye target and added a 10cm LED strip (24V compatible with my Ender 3 Pro). The LED strip was soldered directly onto the wires of the hotend fan, which are conveniently located...

The Petgfang works marginally better, but the bullseye duct truly shines with this nozzle. I therefore created a base that is compatible with both the Ender 5 and the Ender 3 for direct drive and bowden setups respectively. I use it in conjunction...

This remix uses all parts from the original SpeedDrive v1 by sashalex007, sourced from https://www.thingiverse.com/thing:2759439.\r\n\r\nThe design relocates the extruder in the Y axis to clear the posts on either side of the build plate, eliminating...

This is a Remix of the Bullseye Blokhead. ...I'm calling it the "Slim Edition" as I've removed the chunky bits from the bottom to improve the visibility of in-progress prints.</p> <p><a...

Descriptionon-target bullseye door. This can be a one shot latched door when mounted hinge to the bottom or it can be an open swing entry and re-close door when the hinge is mounted upward.This on-target fixture was designed for the 6-Shot Disc...

Instead of making a simple angled bracket and gluing it to the bottom, I combined it with the insert for the Bullseye like [Sixteenbit](https://www.thingiverse.com/Sixteenbit/about) suggested, but I wanted a cleaner solution. This design can...

I was going to make a simple angled bracket and just glue it to the bottom but Sixteenbit had the idea of combining it with the insert for the Bullseye. While his idea does work, I wanted a (IMO) cleaner solution.This can accommodate a LED strip that...

I was going to make a simple angled bracket and just glue it to the bottom but Sixteenbit had the idea of combining it with the insert for the Bullseye. While his idea does work, I wanted a (IMO) cleaner solution.This can accommodate a LED strip that...

Fixed all the flaws, slightly reduced the fastenings for the bar.

Bubble pot Original dimensions: 95 cm high 10 cm wide. ... Can be scaled to a smaller size and still has good printing properties.

... handle/holder/handle to print yourself. ... Round side just dip in homemade or store-bought bubble water/suds and go! -3D model made of two parts for a print without supports. ... -3D model assembled into one part (supports needed) Have fun printing!

Ride like the wind, Bullseye! ... ===

This fits the Bullseye Fan Duct system using the stock 4010 fan.

bubble light

WATER BUBBLE

Bubble ring

bubble-box

Bubble wand

Bubble Cube

WATER BUBBLE

Bubble wand

Bubble Blaster

I designed this mount to ensure the stock bed level sensor is positioned as closely as possible to its original location when using the Bullseye duct and ValleyBot's mount for it. Specifically, this custom mount was created in response to ValleyBot's...

Create this bracket to mount the duct for the fan layer for bullseye; Scale up 1000 percent.

Remix of the great Ender3 Direct Drive Bullseye by jan_michael . Just removed some material to make it even lighter. ...

I've taken the original design by Ben White and reworked it to seamlessly integrate with E3D V6 hotends, including clones that feature a bullseye-style duct.

Just finished crafting a remix of Ender 5 and the original Pet Fang Bullseye. ...If you appreciate my design, consider tipping it at https://www.paypal.me/Djdenzo