buffer tube end cap 3d models

its based kind of on the kns adapter, you screw the threaded piece into the rifle, then attache the picatinny with a 1/4-20 socket head screw to lock it in 100% solid printing is a must

Still in production mode, awaiting final assembly according to precise military standards. ...Dimensions carefully crafted to meet strict specifications.

Note: This model has never been tested.

This end cap will go on the end of a 63mm diameter drain pipe.  There are two holes to allow it to be held on with self tapping screws.  It is slightly oversized to allow a length of ladder/window line to be held in place.  If you want it tight, then...

Fell flat off the door frame and landed squarely at the end, causing a perfect break of the end cap in the process. The handle had been loose and was about to fall off altogether, so I quickly swapped it for a good one and made a simple replica. No...

The stock end caps are made from a soft plastic (not as soft as TPU) which splits in half due to creep or something. These fit on snugly enough, but could be somewhat troublesome to push on straight. ...There is a 1 degree draft on the inside for a...

As a result, I created the attached rendition of Campy's obsolete EC-RE024 shifter handle end cap. This slides right in and will replace original lost or broken parts. ...Version 2 was uploaded to provide increased spring clearance for the thumb lever.

An end cap that fits tightly to the maximum. Can of course be provided with felt glides. The advantage of this is that the felt glides can be removed more easily and the table remains in its "original state". Depending on the thickness of the...

The missing end cap on my Weider Pro 4950 home gym is merely a cosmetic issue, as I aim to sell it. Fortunately, you can replace this part by altering the FreeCAD file. ...To ensure a seamless appearance, I employed black ABS, fine sandpaper, and...

End cap for 22.1mm outer diameter and 18.2mm inner diameter handlebars. Used screw M5 40 mm for hexagon. It is possible and 30 mm, but it will be back to back. You can also use an ordinary goika, but self-locking is better. --- Торцевая...

These are caps to go on the ends of a "1 inch" tape measure antenna. Help save eyeballs and protect against the sharp and pokey bits of the antenna. Inspired by Becky Stern's tape measure yagi antenna project. ... Fusion 360 f3d file included.

I created this cap to fit over the end and stop the drifting spool from falling off. Solved the problem. ...I thought others might find it useful...</p> <p>UPDATE: 1/27/20</p> <p>I added a Chamfer on the edge to help with fitting on the roller.</p> ...

I'm impressed with the End Cap 2's snug fit, thanks to its small nub that keeps it securely in place after tapping it in. ...This is my first foray into designing custom parts for my printer, and I was surprised by how effortless the process was - a...

To replace missing end caps on my father's mountain bike, I designed and printed custom ones with a 25mm diameter hole fit. The attached image displays a personalized version featuring his initials. ...Print settings include 25% infill, one shell, 0.15...

This lens cap is designed for the end of a 0.965-inch astronomical eyepiece, fitting all such eyepieces. Creating it from HDPE offers flexibility; however, its durability remains untested. Additionally, 1.25 and 2-inch sizes are available with a...

This end cap is designed to fit multiple models of dishwashers. Print it upside down on the U-face. Use supports for small areas (try settings for 5 square millimeters or less). Do not use PLA at all. ...I'm not a fan of ABS, but you can try using it if...

GE Dishwasher Handle Endcap This is a replacement handle end cap for the GE Dishwasher Model GDT580SSF5SS. Here is a good video on how to replace the entire handle, but I designed and printed this part to just replaced the broken one. ...

If I remember to find the make/model, I'll post it here. The stock end caps are made from a soft plastic (not as soft as TPU) which splits in half due to creep or something. These fit on snugly enough, but could be somewhat troublesome to push on...

I previously constructed a 3D printer featuring 30mm Bosch rails and used the supplied end caps. However, I recently decided to create custom replacements for these components. The initial design was created using Solidworks, but encountered issues...

I cracked my fragile acrylic end cap by cranking down too tightly, so I carefully measured it out and printed a brand new one right away. I had seriously considered upgrading to this awesome model here http://www.thingiverse.com/thing:2078706 but I...

If the emmaljunga brake pin doesn't reach the wheel locking holes, it means the plastic part has worn out from the pedal end of the cylinder. In that case, if the plug wears down, the metal tube starts breaking away at the pedal itself and the brake...

Cap for 30*60 metal profile

This new end cap adds tabs that align perfectly with the Pi's mounting holes, securely holding the Pi in its place. I've tested this with both Raspberry Pi 3B and 3B+, but it should work for any Pi that this case works with since the screw mount...

This is a custom end cap designed specifically for the Orion ED80 telescope model, engineered to produce a distinctive "cross" diffraction pattern on bright stars that's ideal for astrophotography. Unlike other telescope designs like my 10-inch...

I also beveled the parts that fit into extrusion but its still a really tight fit. interface of the pegs between end cap and the tray should be reasonably tight but may depend on your print settings. I've added slight bevels to the points touching...

This modified end cap is specifically designed for application with thicker gauge tubing than the initial Eventorbot version. The new design allows for a snug fit onto open ends and the square hole at the top. ...Furthermore, the slats are angled to...

Plastic end caps that hold the crossbar on came broken. Coleman only wanted to replace the cot but I didn't want to create more garbage. Thankfully I have a 3d printer. Have used them with the replacement for about 8 nights and so far so good. I...

This particular model has been tested and has not fallen out of my handle while I have lost 2 of the original zuca end caps. I have included two separate models, one as a standard black cap and the other has the riddler logo on it that i used for...

Easy way to turn plastic gutters into a NFT hydroponic system: Attach PLA caps using PVC primer and PVC Cement.\nUtilize Mounting Brackets for downspout channels from http://www.thingiverse.com/thing:1687100\nApply Net pot Blanking plate from...

Made on TinkerCAD (link) A lot of our old player piano rolls, also known as a pianola rolls, were in bad condition, so I was looking for an easy way to make new end caps for them. Common brands for these include Master Touch a.k.a Mastertouch, and...