buffer tube end cap 3d models

The buffer tube itself is modeled after direct measurements from a Palmetto State Armory mil-spec diameter tube, ensuring compatibility with any mil-spec stock you might have lying around. Credit for the base design of the controller slot goes to...

Just a simple Cap for a 25mm tube. ...I use it with my other designed Parts for my Weather Station.

I lost the cap of my glue tube, so I had to print a new one - quick designed, quick printed.

Simple cap to seal a caulk tube after use so it doesn't dry out. Category: DIY

This is to extend the silicone tube by attaching another silicone tube to it.The end can fit inside 2mm drain hole for cleaning the inside of SLA prints with IPA.For use with printable's ResiVac1000.To cure the end, insert handle of nozzle cleaning...

It is a quickly designed cap for a silicone tube. You may want to scale down .1% for a tighter fit.

4mm TPFE Tube capYou can cap with the tip of the filament slightly protruding.TPU Fillament 0.4mm Nozzle 0.2mm LayerNo Support

simplemente una tapa para un tubo hueco y protegerlo de la lluvia. ... Simply a cap for a hollow tube and protect it from the rain.

Yet another caulk tube cap. This one uses a cone washer available at a hardware store. Used 0.2 mm layers. ...

Yet another caulk tube cap. This one uses a cone washer available at a hardware store. ... Used 0.2 mm layers.

This is a simulated medical tube replacement cap designed specifically for use in a simulation lab setting, allowing for cost-effective part replacement and training purposes only.

... into a coin bank? ... This cap will fit any of the following designs. https://cults3d.com/en/3d-model/game/mario-stash-tube-tall https://cults3d.com/en/3d-model/game/mario-stash-tube-medium https://cults3d.com/en/3d-model/game/mario-stash-tube-short

MIL SPEC Buffer & Castle Nut has no internal return spring. Reinforced for 3D printing, its exterior looks identical to a standard Mil Spec one. ...Don't miss checking out more cool designs and follow daily doses of kooky creations - I upload often!

I remixed lichtzeichenanlage's PTFE tube cap so that I could mount multiple to the top of my Lack cabinet. I simply added a base that can be glued to the top of the cabinet and added 8 caps. I have 8 filament spools in dry boxes and this allows me...

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=49604 Instructions Using the following options: clearance = 0.4 number_of_tubes = 1 coin_type = 13 number_of_coins = 50 tube_wall = 2 fudge_factor = 0.975 generate_tube = 1 generate_cap = 1

I'm crafting a basic cover for a lubrication tube right now, I actually require one for the opposite end of my lubrication tube, so I created one on my Anet A8 using flexible filament.

A roof rack tube cap replacement part. ...Video of printing process: <a href="https://www.youtube.com/watch?v=2nKNPVRSM-0">https://www.youtube.com/watch?v=2nKNPVRSM-0</a></p> Category: Automotive

Hi, this is simple Antenna cap. ... Any antenna tube with 3mm fits nicely, no wobbeling! If it is to long, just scale it down (or up) to have it optimal for you. Printed in TPU 95a. ...

What I really needed was caps for my primer tubes that would allow me to load up for a session without worrying about primers spilling everywhere in case of an accident. ...These caps have just the right tension on the primer tubes I use with my Hornady...

It might be a tight squeeze, so use a 4mm drill bit at both ends if you're having trouble getting the tube through. If that doesn't work, try drilling the whole thing with the 4mm drill bit and see if it holds up. ... Use M4x8mm screws to mount it to...

Once you've used up all your paper, you'd normally just toss the empty tube in the trash, but this clever cap gives new life to these small tubes by transforming them into versatile containers for various purposes. You can get creative and use the...

i got tired of the rubber stopper on the battery tube so i just made something to extend it and screw on without having to deal with the stopper

I'm in need of adjustable end plugs for my printer table, which I built from 50x50x2mm square tubing to perfectly fit within an IKEA Lack enclosure. I created a better table because the original Lack table was not sturdy enough to support a printer,...

Fits snugly into the end of a cardboard tube from toilet paper or a paper towel roll. Lets you reuse cardboard tubes for containers or a small drum. Vase mode and regular included. (Vase mode version uses half as much filament). ...OpenSCAD files...

To use it, simply remove the skimmer from the tube and insert the cap into its place; it might not be completely watertight, but it'll suffice for working on the pump. I've also designed an additional cap with a threaded design for the water outlet,...

This is a simple, customizable grated lid/cap/top for tubes, bottles, and other items. It's an OpenScad file that can be easily edited through the customizer here on Thingiverse or purchased using OpenScad. If you need to screw the caps into...

I designed this thing to hold the end of the secondary bowden tube at the vertical top profile where this is mounted. This is designed to be used such that the bowden tube is pushed all through the hole. The hole is not a straight through hole, it...

The original cap had a too high inner for my crokinole tiles and was not properly closed (possibly there are tiles with different heights). I have added two pads at the bottom and top of the tube to better accommodate the chips, but this is not...

This innovative device serves as a straightforward cover-up cap designed specifically for standard cage components featuring 1-inch lens tubes, ensuring optics remain spotless during periods of non-use. ...Constructed from durable PLA material, it...

After a small storm and an emergency dismantling of the trampoline (in the middle of the night), I lost some plugs of the trampoline tubes. These caps are used to protect the inside of the net. ...Here they are printed and the trampoline is ready to...