buffer tube 1913 adapter 3d models

适配威迪PDX的AR托芯改件

Shining optical light pipe

Made this cause I had to have a quick fix for my plate that snapped after dropping it and is holding very well

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Ridges sections must be oriented face-upwards, while rounded areas should be positioned on their sides.

Ergonomic accessory designed for connecting devices together via standard fitting on either end for easy, versatile setup.

Customized version of https://www.thingiverse.com/thing:4199907 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4199907

Picatinny rail GoPro to Picatinny rail 1913 Use hard TPU

I remake this with a holding plate in the middle to be able to use an m5 screw and lock it on the lower receiver.

Picatinny Rail drawn using the actual MIL-STD-1913 dimensions.Model units are inch.

Universal adapter for standard 100mm clear tubes now fits perfectly into 40mm threaded tubing without any additional support required.

this model is based on the FGC9 AR buffer-tube mount https://www.printables.com/model/192633-unw-fgc9-fgc6-mkii-or-mki-thread-in-ar-buffer-tube but you need this 3d model for the FGC68 to get the same look this replica model is fully 3d printed made...

We had a tube rotator but it only had adapters for the 10mL tubes. ...Made a model that prints in one piece that will hold 10 1.7mL microcentrifuge tubes.

Adapter from Gerlon Tube for sanding to Karcher WD6 tube.

I acquired a vintage 1913 Oliver typewriter at an antique shop. The machine was in decent condition, yet one of the spool caps was nowhere to be found. To address this issue, I designed and printed a replacement part. ...Although it's uncertain whether...

We created a custom tube holder, replacing an existing rotator with limited adapter options, which was specifically designed to accommodate only 10mL tubes. ...We then developed a 3D model that prints as a single piece and can securely hold ten 1.7mL...

Buffer Dolly

Buffer tank

buffer tank

I have successfully tested this in PLA, spinning full tubes at 15,000 RPM (around 21,100 RCF) for ten minutes at a time without damage to the tubes or delamination of the adapters. You should test your own tubes and prints to make sure that they can...

This adapter is ment to connect two 36mm inner diameter flexible PVC tube to each other. I printed this with a Prusa MK3s in quality mode and the tube is easy to screw in and has a nice tight seal. ... Hope you find it useful for your own purpose :) ...

This is an adapter designed to hold 2mL microcentrifuge tubes in a Hamilton 24 position tube carrier (SMP_CAR_24_A00). Hamilton manufactures a similar part (188102) for the 32 position tube carrier, so I based the design of this model based on that.

... old design delaminated along print layers while she was centrifuging something. I redesigned to prevent this from happening to anyone else. May 7, 2017: Tapered the top of the adapter into a flat dome, making it easier to uncap and remove tubes.

ADAPTER FOR FESTOOL OF1010 MILLING MACHINE AND FESTOOL VACUUM TUBE

Snapmaker2.0 Filament 6mm Tube Adapter For 3D Printer Head 

Dyson vacuum adapters extend suction to 30mm tubes.

An adapter to mount tubes onto 120mm fans

A 3D model of PAPR Tube Adapter for 3M Respirators

Air tube duct adapter 100 mm.Spray booth needed a hose. ...I use a 100 mm flexible tube.The tube needs to be removable.

This is a bowden tube adapter for an Anycubic Mega S