buck converter raspberry pi ender 3 3d models

Also added cutout for USB passthrough on front of the draw Pi runs at about 45c while printing (No heatsinks installed) Hole spacing for LM2596 used are 58mm x 32.5 Hardware required 8 piece M3x6mm (Pi and Converter can use 2 each if you haven't got...

I built this dock specifically for my raspberry pi, which is already encased in a protective housing and running octoprint. The dock can be easily positioned on either side of the printer and neatly slots into place within the 40x40 aluminum...

I wanted a mount that connected to the front end cap of my Ender 3 instead of on the top rail. ... It should work with Ender 3/Pro/v2

This is a remix of Harryb1991's RPI4 case with added rails for Ender 3 and CR-10

Raspberry Pi Camera Mount - flexibility, no screws, no other hardware required. This is another raspberry pi camera mount. I made this by making modifications to the files below. They were great but didn't allow the flexibility I was looking for. I...

Remixed from (used the slots to fit into extrusions) https://www.thingiverse.com/thing:4751688 I already had a case for my Raspberry Pi that I Knew fit perfectly so I designed this little caddy that sits in the extrusion slots and supports the pi on...

I also wanted to have a relay (controlled by a Raspberry Pi) and a buck converter (to power the relay and the Raspberry Pi) directly fitted into it. The cover consists of two parts: the base and the side cover, which is bolt-on. The switch can be...

For Raspberry Pi 4B. I couldn't fine one with rails, so I remixed this in Tinkercad with https://www.thingiverse.com/thing:4176051 I had to make the top taller to avoid needing supports, so there is a little gap between the front i/o and the case. ...

To take it to the next level, I drilled a hole into the case to give easy access to the gpio pins on the raspberry pi. This modification should be adaptable to most Creality machines, but confirmation is needed. ...The cap remains unchanged from the...

None of the existing Raspberry Pi stations I found included accommodations for fans, proper airflow, camera cables, the USB port, either HDMI port or the audio jack. This design aims to address all of those issues. The base clips to the existing...

I am planning to make another LCD screen into the top cover, for OctoPrint. I have included the f3d design files so you can make changes and tweaks. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2...

I wanted to use this case design for my ender 3 but wanted it to stay in place but also be easily removeable if needed so I created this thin but solid mount holder that attaches to the printer at just the right distance from the USB port for a short...

This is a simple case for a buck converter with a USB port - perfect for powering a Raspberry Pi from your printer's power supply. Here's the buck converter I used:...

Meshed together two different Camera Mounts that were already on Thingiverse to create a Ender 3 S1 mount that works with my Octoprint camera. ... Update: Added version 1.1 that makes the camera mount slide on the the printer arm much tighter and fits...

mount it anywhere.... ...If you already have your pi in a case use mounting holes at back...

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.02mm Infill: 25% Filament: Hatchbox PLA Notes: Infill doesn't matter very much. Design is mostly solid. Print in given orientation. ... ...

... the right side. For right side optional drawer see: https://www.thingiverse.com/thing:5138213 or https://www.thingiverse.com/thing:5138213 It's my first remix ever, so any suggestions are welcome. Printed and fitted on my Ender 3 V2 Neo.

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.02mm Infill: 25% Filament: Hatchbox PLA Notes: Infill doesn't matter very much. Design is mostly solid. Print in given orientation. ... ...

Remix of this to fit a Pi 5's slightly different IO. My modelling skills are weak, tolerances could be better, etc etc. ...But it works.

Remixed from https://www.thingiverse.com/thing:4192636 to place the Pi on its side so as to take up less space. Also removed some of the port holes next to the power cable. ... Re-mixed in TinkerCad.

RbPi holder for Ender 3Pro/v2 Remixed dual-sided SD slots, and enable screw holes to print without support. ... Compatible with 9cm * 6cm cases like this one in the link below: ...

I didn't put a fan in the design because I have modded the original 40mm controller fan with a 80mm fan, it pushes a lot of air through the vents, should also be able to cool down the Pi. Fan Mods I used: ...

I loved [this design](https://www.thingiverse.com/thing:5201485) that used the original drawer housing, so I expanded it to cover the whole front and added supports for a (buck converter to power the pi from the printer's PSU) and a relay (for use...

Link to the video where I use this case: "Adding a Noctua 60mm Fan to the Ender 3 Pro's Power Supply (PSU)" https://www.youtube.com/watch?v=C4raTp9DZa0 Link to my RC channel: https://www.youtube.com/channel/UChb38m6f-uV_DL-LkGiD3NA The LM2596s Buck...

This motherboard cover is compatible with the Ender 3 V2 I modified the file to accept a 80x80x25mm Noctua fan and that still has space for 3 buck converter. You need these feet to get the 3d printer higher, they fit very well.

Rescale + some small edits to fit more smoth on Ender 3v2 (0.5mm smaller) Scale for 65x35x18 mm buck converter with display

... Plus Case Specifically Designed for the Popular Creality Ender 3 Printer. ... This case is a perfect fit for those who want to integrate their Raspberry Pi 3 A+ with OctoPrint, using an 0.8 meter USB cable and a buck converter to output 5V seamlessly.

This is a Remix from: https://www.thingiverse.com/thing:3164882 and https://www.thingiverse.com/thing:3248551 I tried to mount the original buck converter case to the v slot but i found out i was having trouble that it wouldnt stay in the v slot...

... with special tops to prevent interference with the box: https://www.thingiverse.com/thing:3956434. Left Lid: default Right Lid: https://www.thingiverse.com/thing:3767380 Add support for SKR 1.3/MKS Gen L with two additional buck converter mounts.

I needed to accommodate this larger buck converter for 12v, since I converted my PSU to utilize a massive 120mm fan for complete silence. ...(The 120mm fan model is from here: https://www.thingiverse.com/thing:5217090) Worked out perfectly, and looks...