buck converter raspberry pi ender 3 3d models

Parts: 2 x Nuts #4-40 x 6mm long 2 x Screws #4-40 x 3/16" 1 x Buck Converter (Tuned to 24V to 12V) 1 x Noctua NF-A4x20 FLX 1 x JST Plug 2 x Zip Ties Be sure to tune the buck converter to 12V before soldering it to the fan. ... ...

A modified/mixed version of KyloBen (https://www.thingiverse.com/kyloben/designs)'s flexible camera mount (https://www.thingiverse.com/thing:4871420) and Codemonkey1973 (https://www.thingiverse.com/codemonkey1973/designs)'s Pi camera mount...

A modified/mixed version of [KyloBen](https://www.thingiverse.com/kyloben/designs)'s [flexible camera mount](https://www.thingiverse.com/thing:4871420) and [Codemonkey1973](https://www.thingiverse.com/codemonkey1973/designs)'s [Pi camera...

I was searching for a rugged weather-resistant case that could adapt to various Raspberry Pi camera projects. I found this glass lens online, and it seems like just what I need: http://www.dx.com/p/glass-lens-for-flashlights-33mm-10-pack-5644. To...

This setup enables a Raspberry Pi 3 or 4 to be securely fastened under the LCD controller screen of an Ender 5 printer. Two M3 screw holes are provided, one requiring a 20mm M3 screw for added stability as it passes through both the PI's board and...

Raspberry pie model made in Autodesk Fusion 360

I also utilized an alternative LCD display, the MPI3508 3.5 inch model (I trimmed the small components shown in the picture - red arrow). The hole for the cooler measures 30mm in diameter. There are five holes to secure the bottom of the box using...

I also used another LCD display MPI3508 3.5 inch (I cut the little things shown in the picture - red arrow). The hole for the cooler is 30mm diametter. ... There are 5 holes to screw the bottom of the box (M2,5 screw) 4 holes for pressing the stack...

PiStation: the raspberry pi case for my retropie project. I give credit to "jhample" for the core design of this project because I used his design as a model for my own. This is a completely rebuilt model that can accept a 30mm cooling fan and a...

The popular Raspberry Pi single-board computer is a great addition to many makers' projects, including the DIY Ender-5 3D printer. ...However, one of the challenges that makers often face when integrating the Raspberry Pi into their 3D printing setup...

This is a remix of tobbi007's design, where I've introduced several key modifications. The top piece has been thoroughly altered, while the bottom component remains unchanged. ... Changes Implemented: RPI4 camera cable slot has been added RPI4 GPIO pin...

Remixed from brendanrawrs design Changes: - Moved the fan to the back of the case. Fits a noctua 4020 fan just right. - Removed the need for T-nuts for the v slots. Just slide it in now. - Moved the airflow holes to the top of the case. - Added...

Remix and add the honeycomb all the way across the design to enclose the fan. This adds a more clean look. I used this fan and it fits tight enough that you do not need to use screws to hold the fan in place. ... ...

This camera mount is designed for use with the Solid Bed Mount set produced by https://www.th3dstudio.com/product/cr-10solidmounts and a Raspi camera v2. The goal is to lower the lens so that the nozzle is more visible than it would be using the TH3D...

Austin3dprinting's STL files had some errors, so I re-did them. ...All of the arms now have a smooth inner profile, and the camera+final arm STL file is now split into 2 files so you can distance them on your printer.

My camera wouldn't snap into place because the hole was too small, so I expanded it slightly and adjusted its position upwards to get a secure fit.

I'm using a mix of different stuff I've found around here to keep things organized and make life simpler, it's working out great so far!

Austin3dprinting's STL files had some errors, so I re-did them. ...All of the arms now have a smooth inner profile, and the camera+final arm STL file is now split into 2 files so you can distance them on your printer.

They fabricated a new back/lid for the case from scratch, opting not to utilize the one that came with the original design due to its seemingly misplaced functionality.

I relocated my Ender 5's electronics enclosure to the back, using [rsteube's rear mounting brackets](https://www.thingiverse.com/thing:4541329) and then printed his [Raspberry Pi mount](https://www.thingiverse.com/thing:4579858) for inside, so I...

LED strip connector designed specifically for the Ender 3. Intended use is with two 12V LED strips, connected end-to-end in series configuration. This eliminates the need for a separate 24V to 12V converter, often recommended by other solutions.

The design is based on strict measurement values found here: https://learn.adafruit.com/introducing-the-raspberry-pi-model-b-plus-plus-differences-vs-model-b/mounting-holes\r\n\r\nI designed it to be easily modified for custom covers with various...

This is a box for RaspberryPi3 and DC-DC converter.

... of my Ender 5 supports, but I couldn't locate one. ...This is intended to simply hold a Raspberry Pi on the printer (for OctoPrint etc) in place. The design fits snugly against the profile of the Raspberry Pi and elevates it about 10mm above the rail.

... holes, as this can compromise the structural integrity of your finished product. During my development process, I drew inspiration from the Ender 3 Raspberry Pi Camera Mount available on Thingiverse (https://www.thingiverse.com/thing:3188580).

I was eager to print Rasmushauschild's Pi Boy case, which truly impresses, but unfortunately, none of the files functioned properly on my Makerbot 5th Gen printer. ...I corrected the issues and re-uploaded them because I'm aware that others have...

I modified an existing design, the Ender 5 Raspberry Pi Camera Case - End Stop Mount, and integrated it into a frame clip mount to achieve the ideal camera angle for capturing the nozzle during printing operations.

... RPi 3B+, particularly with its four new Power Over Ethernet pins. ...It also happens to be compatible with the RPi 2B and 3B models, along with most Pi HATs. ...Could you let me know if you've had a chance to test this case out with the new PoE HAT?

Recalbox themed case for RPi 2/3

This is a remix of Balmung83's design on Thingiverse, specifically https://www.thingiverse.com/thing:2205034.\r\nIt was crafted with the intention of housing a 50x50x10 fan that utilizes self-tapping case fan screws for secure installation.\r\nA...