bubble magus curve 5 3d models

This is a DIY 3D-printable base for a Bubble Magus Curve-5 Protein Skimmer.

Created this replacement part for the Bubble Magus Curve 5, it's hard to find these rubber feet replacement and very easy to lose them when cleaning your skimmer, this probably will also fit other Bubble Magus models if the feet are the same.

This STL file is specifically designed for the Bubble Magus protein skimmer bubble plate, boasting a custom twist that features upward projecting tubes to optimize airflow within the skimmer's body. Due to the messy state of the SLDPRT file, I won't...

A stand for the Bubble Magus Curve 5. I found this height allows me to tune the skimmer very finely and product a super thick skim. The aim with this design was to provide stability but not take up too much volume in the sump This is aimed at the...

Customized version of https://www.thingiverse.com/thing:3759895 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3759895

Extension feet for the Bubble Magus Curve Skimmer. 3 sizes depending on your need. ...Uses original rubber feet.</p>

Extension feet for the Bubble Magus Curve Skimmer. 3 sizes depending on your need. ...Uses original rubber feet.

The Bubble Magus Curve Skimmer Extender: Boost Your Footing with Ease Three versatile size options to suit your every requirement, featuring authentic rubber feet for a secure grip.

My friend needed a custom fit for his Curve 7 to match the sleek blue accents in its sump area. The result is exactly what he was looking for. All of these parts are designed to replace existing ones, except for one minor detail - the air knob cover...

impeller for the protein skimmer from the Bubble Magus Curve A5. Designed for the original DSP-1000 pump. ...I didn't like the standard one, I had to turn the air down for the skimmer to work properly, with the new impeller the skimmer works with the...

I've reworked the bubble magus screw in 3D to make it sturdy enough for a tight seal. Be cautious not to overtighten, as this may render it fragile and prone to breakage, but with gentle handling, it will perform its job effectively. ...This redesigned...

I modeled this because I'm thinking of adding a float switch to my skimmer and didn't want to drill the original. ...I thought it might be useful to others that have either lost or broke theirs, so here it is.Note: The pictures are of my first draft,...

bearning 625zz pulley 6 мм 16 teeth motor 25GA-370 12В,...

I created a new cup that could withstand heavy use. To design it, I had to break my old cup, which was fragile and prone to shattering. The experience taught me what I needed to avoid in the next one. Using computer-aided design software, I drew up...

Modification to Bubble Magus filter roll to enable two simultaneous water draining processes.

The user interface of the DC drive is a bubble magus, acting as a straightforward container for its operation.

I have an extended waste tube for easy emptying of my skimmer cup. ...I got annoyed fishing it out of the water every time I wanted to use it. Other skimmers come with clips so I designed this to fit a Curve 6 or NAC 6 cup.

... time I wanted to use it. Other skimmers come with clips so I designed this to fit a Curve 6 or NAC 6 cup. ...Print Settings Printer: Sapphire Plus Rafts: No Supports: No Resolution: 0.2 Infill: 100 Filament: YoYi PETG Orange Category: Hobby

To resolve this issue, I replaced the clogging sponge provided by Bubble Magus with a bubble trap and air outlet. This ingenious solution works flawlessly, eliminating the need for frequent maintenance. Designed specifically for the Bubble Magus...

The Magus Male comes fully supported in both Lychee and Static STL format.

Bubble-magus NAC7 which were called later as C7, used the Atman PH2500 pump, replaced with SP2000 pump. The skimmer has two major parts: a housing with bits and bobs to make skimming work and a pump with a needle wheel to make bubbles. The former...

I designed this for my Bubble Magus curve 5 is a 17x17cm platform with 16cm long legs (You need to print 4 legs) I have 2 types of platforms one is solid and the other has indentations to keep weight down. ... Legs are 1x1cm

http://www.thingiverse.com/apps/customizer/run?thing_id=615256 Instructions Using the following options: vertical_axle_holes = yes use_reinforcement = yes slope_stud_rows = 2 curve_stud_rows = 2 dual_sided = yes curve_type = convex stud_rescale = 0.5...

http://www.thingiverse.com/apps/customizer/run?thing_id=615256 Instructions Using the following settings: vertical_axle_holes are turned off use_reinforcement is turned off the slope_stud_rows count has been set to 1 the curve_stud_rows count has...

The dragon curve is created by folding a piece of paper five times to the right.

Enables diversion of water flow to circumvent filtration process, Permitting selective passage of certain particles or water through the filter, thus retaining essential nutrients such as phosphates and nitrates within the water column.

I have enjoyed the MiniQ protein skimmer for my nano tank but the included holder doesn't work for me. I find that whenever I try to move the cup, the hole skimmer slides on the mount regardless of how tight I have the screw. ...So I designed this mount...

... Ferrorama with precision. ... The device requires a deliberate tilt of 22.5 degrees. To build the Ferrorama, you'll need the following materials: Four screws are necessary for assembly. ...A screwdriver is also required to drive them into place.

Ilthus Mora the Magus (Modular Slathaai Arcanist)Ilthus Mora is one of the first Slathaai, born directly from the first brood of eggs laid by the corrupt Avatar of Holmuran. As one of the Originals, he possesses such an ability for Arcane...

bubble level tube D9.5 L25