bu ton 3d models

 Only a tiny bit of glue is required (primarily near the pivots) as it will squish and spread so you don't want a ton of glue oozing out from between the parts.  The pivot pins have a hex that is just a rough guide for alignment.  You will likely...

Sorry I didn't clean it up - busy trying to get this going and then printing, not a ton of time to clean it all up. I'll post an update soon. Post-Printing: Screws: Sorry folks, I used a lot of smaller 4-32 SAE screws I had from one of those cheap...

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 300 Infill: 15 Filament: Any Any Any Notes: I shaved a ton of time off printing by reducing my tops/bottoms to 2 layers. You can see the infill through this,...

Parts i used: ESP32_CAM module: https://s.click.aliexpress.com/e/_DD3fJIR PIR module: https://s.click.aliexpress.com/e/_DmmGQWL 5.5mm power plug:https://s.click.aliexpress.com/e/_DkJxaDv (This will be used to charge the internal batteries, since i...

Just the fact that they stick to each other gives them a ton of stability on any battle-map, but if you really want them to stay in place, you can throw a piece of sheet steel under the map! Optionally, of course, you could also pick up a...

DD is Direct Drive without DD is Bowden HO is "heat off" at third visor (saves a ton of power) so The Stack is Bowden heat on entire print. TheStackDDHO is The Stack for Direct Drive with Heat turning off at Third visor. 200mm Delta variation added...

Tons of thanks to profezzom for his Marksman-H combat remote. The goal of these parts is to provide printable parts for a Training Remote scratch builder that doesn't have access to the tank model kit parts. I tweaked some of profezzom's parts a...

The D7 comes with a metal cover which isn't exactly light tight, weighs a ton and doesn't allow you to view progress of your ongoing prints. This replacement cover is lightweight and transparent, whilst still protecting the resin from stray UV in the...

Her performance was met with favorable reviews, and she soon became a staple at the theatre, taking on roles such as Maria in Murphy's Citizen, Rosetta, and Miss Tittup in Garrick's Bon Ton. She also spoke the epilogue to the Spanish Barber, or the...

Many were bipedal, and others were quadrupedal, and could weigh over 100 tons. These ones really resemble the ones in the movies. """""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""" Clean topology; Mesh subdivision; ...

Cimarrón CMR-4-1F Mass: 40 tons Tech Base: Inner Sphere Chassis Config: Biped Rules Level: Tournament Legal Era: Clan Invasion Tech Rating/Era Availability: E/X-X-E-A Production Year: 3080 Cost: 7,022,680 C-Bills Battle Value: 1,278 Chassis: Colonial...

If you know you need a centrifugal compressor but you need a ton of power for your application, you'd almost certainly be better off running with a model that was designed from the get-go for some kind of RC brushless motor (or another...

But naaah let's print something with a TON of moving tiny parts instead! Oh, and while we are at it, why don't we do something where all of the little parts are chained together, like little droplets of filament love on the table, no way will that...

Added a jointed version, it will require you to construct some twisted wire joints in order to assemble (tons of videos out there, basically make one twisted wire loop, then create a second one linked to the first). Unlike the first version the...

Printability has been improved from "needs an SLS machine" to "hey, I bet I could make that work with a few settings adjustments." Final Science Update Some Lift Chicken Scratches: Martian atmospheric pressure at top of Olympus Mons = 0.03kPa...

I had tons of fun making this come together; I hope someone else out there will appreciate it or use it to make another one of the four upgraded staffs! I've done my part, now who wants to kill the Panzer and slap that fire staff together? If you'd...

That left the owners with 5,900 tons of unwanted marble. Some was turned into trinkets like paperweights. Some was donated to a company that makes trophies. A lot was used in landscaping at Governors State University, and at Amoco facilities across...

also will need clevis of your choice to connect to servo horn (I used a solder clevis) e-z connector like https://www.dubro.com/collections/e-z-connectors/products/e-z-connector to lock hinge rod in place (bend other side) 2-56 ball link...

HUGE UPDATE 2018.10.08: This case was my first try to design something for 3D printing and honestly, it was a Frankenstein creation with tons cobbled together surfaces and inelegant but functional edits in Tinkercad to get to the finished design. I...

The OdAZ-885 uniaxial automobile semi-trailer comes with an onboard platform and is designed for transporting goods as part of a road train on roads that allow vehicles to carry loads up to 6 tons axially. Produced by the Odessa Automobile Assembly...

Because some of my previous designs got stolen and commercialised and this project took a ton of time, I've decided to share only 3D designed parts and some enclosure dimensions. This should be sufficient to build the enclosure on your own with...

... OD). Lock nuts are recommended. Polycarbonate is a pain in the arse to print in, avoid !! All the components can be found on microcutter.se/shop and there is a facebook group and a github with a metric ton of information. Category: Robotics

If you do not already belong to that group, I strongly recommend it, as there are tons of helpful people and settings/files posted there that will help you along your way. Now, on to the important stuff... <b>Parts List</b> So, at a minimum,...

Each massive creation weighs about 12.5 tonnes (13.8 tons) on average. All but 53 of the over 900 known moai were carved from tuff, a compressed volcanic ash found at Rano Raraku, where an astonishing 394 moai and incomplete figures can still be seen...

Now you can get one without spending a ton as well!Everything should be printed in the provided orientation and in black filament for best results. A matte black works best but any black will do. I recommend 0.3mm layers with a 0.4mm nozzle for...

Here's what you'll need (i hope i dont forget anything as i build that almost a year ago): Uniball Joint M8: https://www.ebay.de/itm/332491281506 Limit Switches: https://www.ebay.de/itm/174416254645 USB-C Breakout Board:...

And, there's not a ton of extra space for the character ability cards, as well. I may eventually redesign the top layer to be even taller, to give more room for these elements.I'm also considering replacing all the cardboard game elements with 1/16"...

As seen in the pictures, I put a ton of layers of rubber cement (super glue in the MK2 Version) on the handles to make them stronger. Even with these layers, they will break and need to be fixed after a couple of hours of gameplay. Superglue them...

You'd think that an open-source, 3D printed nerf blaster would have tons of tweaks, options, and accessories, but there aren't... All three FDL-2 types look virtually identical, the number of remixes created by the community is extremely small, and...

And thirdly, I'm grateful to Paul Cole, who kindly shared with me a ton of info about his Mega and dual Z stepper functionality. Thanks again! UPDATE: I've added Z-axis pillow blocks to isolate the Z lead screws from their motors. Check out Thing...