broom end caps 3d models

236527 3d models found related to broom end caps.
Curling Broom End Cap
Curling Broom End Cap
thingiverse

This is a simple end cap for a curling broom. Broom diameter is about 28.5 mm. TPU is recommended but PLA is also fine. ...This could be scaled to fit other tube sizes.

Broom  end cap
Broom end cap
thingiverse

Broken component replaced with new one. ...TPU material withstands harsh Canadian winters effectively.

Broom  end cap
Broom end cap
cults3d

Replacement Part Available for Damaged Unit. ...High-Performance TPU Material Designed to Withstand Canada's Harsh Winter Conditions.

Stick End Cap Mount (Mop / Broom)
Stick End Cap Mount (Mop / Broom)
thingiverse

... or broomstick in the market? ... Here is the solution! It's always easier to get the whole stick together with the end cap, but sometimes you just love the stick and you just like to get the replacement for end cap as the end cap does not last long.

Broom Handle Threaded End
Broom Handle Threaded End
thingiverse

Use this to replace a broom threaded end ... suits a 25 mm handle. ...If the thread is loose, put some electrical tape around it

Casabella Broom End
Casabella Broom End
thingiverse

I replaced the broken end of my Casabella broom with a new one using a saw. The old end was stuck tightly in place, but I managed to cut through it and secured the new one with some glue. The design requires support on the button area, and while the...

Broom Stick Thread End
Broom Stick Thread End
thingiverse

Version 3 has a small radius at the end of the thread to help the thread go deeper for recessed broom threads. Version 4 looks a little nicer than 3, features a smaller diameter at the bottom of the thread to clear the hole better, and includes a...

broom stick end
broom stick end
thingiverse

replace old broken off stick end

End Caps
End Caps
prusaprinters

I used 12" x 0.312" (8mm) aluminum tubing on these roller bases. ...The tubing extended out past the end of the roller base about 5mm on each side. These end caps help take up the extra tubing and help hold the system together. ...They look good too.

broom stick Thread end connector
broom stick Thread end connector
thingiverse

Broom-to-Stick Attachment Design The broom attachment is designed to securely connect to a standard stick diameter of 0.9 inches. A threaded insert with an outer diameter of 0.7 inches and a pitch of 0.20 inches is utilized for a secure fit. ... The...

Pontoon End caps
Pontoon End caps
prusaprinters

90 degree end cap and 117 degree side cap.

3030 Extrusion End Caps
3030 Extrusion End Caps
cults3d

Several variations of 3030 extrusion end caps

3030 Extrusion End Caps
3030 Extrusion End Caps
cults3d

Several variations of 3030 extrusion end caps

End caps Hudy tools
End caps Hudy tools
thingiverse

Huddy Caps Securely Fasten Tools and Equipment with Durable End Caps.

End caps for gutter
End caps for gutter
thingiverse

Some innovative end cap designs for the rainwater downspout of a summer house are available.

3030 End Caps
3030 End Caps
thingiverse

The Human: A Next-Gen Product Line 3030 and 3060 End Cap Mark V1

Cue Case End Caps
Cue Case End Caps
thingiverse

To safeguard my briefcase without any plastic ends, I crafted custom-made protective caps.

4040 & 4080 End Caps
4040 & 4080 End Caps
thingiverse

I needed some end caps for 4040 and 4080 aluminium extrusions.

Fire blanket end caps
Fire blanket end caps
thingiverse

End caps for fire blanket where original ones disintegrated with age (poor quality)

Whoop battery end caps
Whoop battery end caps
prusaprinters

End caps to protect your batteries from concrete and bad landings. ...Half a gram for the 300mah cap, 0.7g for the 450-600mah end cap.  Print in TPU with 20% infill

ALTRAX - Profile end caps
ALTRAX - Profile end caps
thingiverse

End caps for ALTRAX aluminium profiles available at hobby-store.pl End caps fit only to ALTRAX profiles. ... Designed for profiles 20x20 , 20x40 and 30x30 and 30x60 in T and V slot versions.

Socket Rail End Caps
Socket Rail End Caps
thingiverse

To prevent my socket pegs from slipping off the track while transporting, I created custom end caps that snugly fit onto the rail's ends.

Step ladder end caps.
Step ladder end caps.
thingiverse

Fits aluminum extrusion profiles 40mm wide by 20mm deep. ...Step ladder replacement feet and end caps for secure installation.

Tronxy X1 End Caps
Tronxy X1 End Caps
thingiverse

... its overall sharpness. ... Two double end caps, one mirrored, are required to reinforce the y-axis, while a single end cap is needed for the x-axis. ... I've recently refined the meshes and incorporated a version compatible with my X-Idler Fix upgrade.

PermaTrack End Caps
PermaTrack End Caps
thingiverse

These are simple end caps for RGB-Man and Dr. ... Zz's Permatrack for permanent pixels on your house. One is a simple end cap and the other has a hole for your cable to enter or exit. ... I plan on adding more caps, 90 degree etc in the future.

3030 End Caps
3030 End Caps
thingiverse

I needed end caps to finish a couple of printers I'm building based on this project: https://www.thingiverse.com/thing:1692666 . The end caps included in the project didn't fit my extrusions, so I made a few of my own. The AutoCAD DWG file and STLs...

tube end caps - 8x6
tube end caps - 8x6
thingiverse

I'm using these caps at the end of my drone frame tubes to prevent them from breaking apart and also to keep debris from entering the tubing.

Gutter end stop caps
Gutter end stop caps
cults3d

This is a standard 100mm (4") diameter gutter end cap, also known as a gutter stop. ...I used it to create a strawberry-growing environment.

Ender 5 End Caps
Ender 5 End Caps
thingiverse

These will replace the black end caps on your Ender 5 printer. ...I made mine with my initial, but the .STL I provided is blank.

Stratocell End caps
Stratocell End caps
grabcad

Packaging foam Stratocell end caps for hif equipment but can be easily modified to anything. ...Includes left and right hand parts