bronchial tree model

The 3D printing process sometimes leaves whiskers or small blobs of plastic which might jam the fully assembled power train unless each stage is run-in until all parts are worn smooth when the whole will operate as designed.   Assembly:1)...

The use of simple metal parts in combination with printed components holds a lot of potential for the future; FreeMenDontAsk is already working on other handgun models. Even outside of gun making, this could be useful for a wide array of printed...

You may have to do some light cleanup, but the fit of the parts should be snug enough to hand press together with no wobble. IOMarms STL- These arms are taken directly from the original wood designs and are generally sized for an IOM, but are not for...

Have a close look at the photos and assembled model (wall_clock_07.stl).PlatesThe bearings are hard to push into place, this is where the bench clamp comes in useful to push them flush into the plates.The front plate needs a 30mm M3 screw to hold the...

WARNING: To make sure you're looking at the latest version of our files and documentation, we strongly recommend that you navigate to the Official Project Page. V-Core 3 The V-Core 3 is a premium DIY kit for a CoreXY 3D Printer with no compromises....

As this is a rather large model it will take a buildplate of 212mm by 175 mm, so this will not fit on a smaller printer's buildplate, but it will fit fine on an Ender 3 and similar printers. My goal was to create a phone holder you can trust with...

If you're using the motor in the BOM or Qidi stock motors use this: xplus-imate-firmware.gcode If using a 0.9 stepper motor you should prin tthis instead: xplus-imate-firmware-optional-0.9-degree-motor.gcode Just place it on your USB stick and print...

rice or sand.Glue if the press fits are not tight enough Testing tolerancesStart by printing the models press_tolerance_test and rotation_tolerance_test from the folder Common parts.Press fit toleranceUse the press fit test to decide which press...

Learn everything about the V-Core 3 on the dedicated project page: v-core.ratrig.com. External links: Buy Kit at Rat Rig Step by step Build Manual Facebook Rat Rig 3D Printer Community Project Page (BOM, Build Guide, Files, Electronics, Firmware)...

Make sure, shaft diameters on knob and potentiometer are the same (6mm or 6.35mm).Model: OEJIndicator: (L)line, (A)arrow, (NI)no ind.Diameter: (50)0.500", (63)0.625", (75)0.750", (90)0.920"Finish: (1)clear gloss, (2)black gloss, (3)clear matte,...

The ability to visualize 3D models in real-time enables users to make informed decisions about color palettes, proportions, and overall aesthetic. This level of precision is unmatched by traditional design methods, making Shining 3D Fashion a...

Those end sections will be the corners of the models that have a section of 4 cells (2x2) walled off to prevent nickel strips being connected incorrectly.4. Make sure the cells are in the correct orientation, you should have a tiled pattern of 2x2...

○ 3 options available § EyeCuSmile_Ribs_V2_RoundedNose.stl - best visibility § EyeCuSmile_Ribs_V2_TriangleNose.stl § Or various developmental ribs models used in the flat pack face covering kit and Version 1 listing of this design. - COMMON...

In the end I think the best way is to simply open up the 3D-model of the whole maze and just put obstacles together one by one. Therefore I Added a few different files (STEP, STL, 3D-PDF (<a...

Or rather, it's a scale model of what that house looked like fifteen or twenty years ago. The wrecked version is closer to how it looks now that it's been abandoned for the better part of two decades. The tweakers have had a field day with this...

From there I just drew out the parts and extrudede them in the modeling tools, then exported them to STL files and printed them out. Project: Laserscythe - Another Open Source laser engraver using recycled doohickeys Project Name: Project:...

Model says 119mm, which would be close.???---------------------------------------------------------------------------------------------------------Printed Parts:&nbsp;Base:___________________Placeholder____________________This is the base of the...

It deviates a bit of what I usually call an "sci-fi astronomical object", because it's an in-spacecraft transport vehicle. I made this model available in 4 scales. I left the model in "halves" that I consider the best way to print it, of course, with...

X type. Density: 2.17 g/cm3 Dimensions: 870 m Model scale: 1:8x103 (10cm) 1:2x104 (4cm) (65803 Didymos) Dimorphos This 170 meter moon has a retrograde orbit around its primary, which means that orbit in the opposite direction of the primary...

This model includes a 14T pinion and a 46T crown which can do a great combination for a start point. The second reduction is between the main axle (previous crown transmits its turn to this axle) and the rear wheel with a belt system. This, the belt,...

&nbsp;The tire model itself isn't chiral. &nbsp;The tire part is only chiral after printing with one side down, and only appearance-wise. &nbsp;Functionally the tire should still be non-chiral until you attach the tire to the wheel at which point the...

... springs, bottoms, top layers and tops. but the latest models are off course the best.Please share your towers so I can see how colorful and tall you can make them.And don't forget to check out my Instagram: fredslund3dGood Luck &amp; Happy Printing!

Neither here nor on the Internet did I find anything suitable for myself and decided to model it myself. In addition, on the left carriage of the X-axis, Aquila has a technological hole for an incomprehensible purpose. And as part of the spare screws...

I first modeled the mold in F360 and printed a few iterations. Once those fit together I designed the MoldMold around it and printed a few more iterations. Printed at .2 mm layer height with a brim to prevent some curling up at the edges - this part...

And you can create two STL files for dual extrusion.&nbsp;Just downlod the SCAD file from the original nameplate:Then install OpenSCAD on your own computer and follow the customizing instructions on this page.Big thanks go out to RLazure for the...

I did not render this model, I just softened and simplified the non-convex model available in the 3D Asteroid Catalogue site, where it is unreferenced, but I think that it is from Hanuš (2017). All three moons of it are too small to make in the same...

BETAFPV LiteRadio3 Controller - ELRS Model On the one hand you don't want to skimp, it's your means of controlling your drone. On the other hand traditional radios are bulky, heavy, and seem to be overkill for me. Got a drone with an ELRS radio? Get...

Alexander is depicted here with large eyes with modeled lids, slightly parted lips, and the characteristic creased forehead. His thick leonine hair is swept up at the forehead in with locks breaking to the left and right. Deep drill work is used...

This is an experimental feature for [TheprofessorODK](https://www.thingiverse.com/TheprofessorODK/about) to add metal spikes to the model. If you like it, please have a look at all my [customizable...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Mounting: The EPL-LED-150W-RT-DIMM...