broccoli 3d model

Prusa Firmware 3.9.0 (MK2S) for Arduino RAMPS 1.4 board In my github repository (https://github.com/cimoalpacino/Prusa-Firmware/tree/MK2S_3.9.0_RAMPS) you can find and download the source code of a working Prusa 3.9.0 firmware running on an...

This is my design of a toy meant to teach children about the effects of an inclined plane on a rope/pulley system and the forces involved.  There are 4 3D printed parts in total and 7 externally sourced common hardware materials.  OpenSCAD Source...

A steel axle would be overkill but a 3D printed one is replaced in minutes and you can use anything with a diameter of 5mm as an axle.Tighter construction -&gt; less wiggling of the parts. Feels sturdy.</li><li><strong>No need for support</strong> in...

You can cut the circle that's sandwich between the two 3D printed pieces with good scissors. The holes for the crews and the tube are harder to make. Be careful, this mesh is sharp and you can get cut. I'M SERIOUS. I managed to make the screw holes...

The information-processing equipment, for its part, will convert hypotheses into testable models and then test the models against data (which the human operator may designate roughly and identify as relevant when the computer presents them for his...

So _1_6_10_7 is 1:600000000 or one in 60 million. The accuracy of the model The model was made taken these features as literal from the book: The spaceship was a cylinder 50km long and 20km in diameter, although it can be expected aliens having...

You don’t want them pulled too tight. Install the Chain Link Cover Clips onto the drag chain links to close the chain. Slide the Cover pieces into place over the Chain Frame Mount and the Drag Chain Arm Connector.Edit 2021/08/07: Added Genius...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

... > No. I planned to use sensorless homing and didn't need it, so I didn't add it. # Misc * [If you are wondering where the beautiful Hemera model in the pictures came from, here is a link ](https://grabcad.com/library/e3d-hermes-hemera-v6-volcano-1)

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...

... weapon. By Alex Wellerstein, a historian of science and an assistant professor at the Stevens Institute of Technology, in New Jersey. Attributions: •Screwdriver by user DAPE, Cults3D (under CC-By-Sa-Nc). •Demon Core modeled by Szadros. ...

... holes. The decorative plugs are designed to be sacrificial, so if you're going to reinstall the knife strip, just print some more plugs!&nbsp;Check out the humorous remix of this design here: Wall-Mounted Magnetic Knife Strip — Home Decor Spoof.

If they are different, please update the Fusion 360 model and re-generate the toolpaths. Also, if you plan on using different tools for the above operations, make sure you update the tools (and associated feeds and speeds) and regenerate the tool...

Most parts do not need support and can be printed using the model orientation. BaseTopMotor and the Lid need “support on built plate only”. MotorMount needs to be rotated by 90 degree on the closed end (the one with the screw holes). In addition, it...

&nbsp;Foam card (if you're not already familiar with it) is a material used in the art world and in crafting or modelling situations, a layer of foam is sandwiched between 2 layers of card, the resulting material is incredibly strong and is generally...

Load your Model into PrusaSlicer and assign both materials. Prusa provides a quite helpful database on their website on how to use all the features in their Slicer that are related to multi-material-printing. After changing the filament there is...

IntroductionThis model provides an effective, low-cost teleprompter for livestreaming and recording. Using a Raspberry Pi and Pi Camera (the cheap, non-HQ one provides great full-HD video in this application), your phone to display your script or...

One important note is that I specifically modeled the pistol's grip to fit the exact CO2 bike pump specified. Theres no guarantee it will fit similar Bike pumps as I took measurements from the exact one I have. DISCLAIMER: By downloading these...

They aren't really required - they just provide some more protection. In addition to the printed parts, you will need the following: 1) 1/4-20 threaded rod, 3" length 2) 2 1/4-20 nuts 3) 2 M6-1.0 hex bolts 16mm length 4) 2 M6-1.0 hex bolts 30mm...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

Ok, so i designed another one because the existing models didn't satisfy me. I also made another design myself previously, but i was still not happy. The reason is that i dont know how all the pumps are designed. - Why do some pumps have...

This should be the first unit from the power supply mob unit -&gt; this contains just leds and has 2 holes in the bottom for an input line and output line end cap unit -&gt; this contains just leds and has a single input line hole in the bottom The...

Thus I found my way to thingiverse and sought for every model that was irregular eventually finding some customizable builders. While the brick making one is heavy, beam kind was cool, but limited to either halfheight simple or up to # shape with...

&nbsp; I also modelled in clips for these PCBs to hold them in place whilst soldering up.I will share my order for my PCBs on jlcpcb so anyone can order once I figure out how :D&nbsp;Tools RequiredSharp knifeLong Nose Pliers&nbsp;Note that the 3mf...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

I got a package of 5 and when I opened them I found that the design had changed slightly and the material they used on the newer models was slightly thinner. The original clips were therefore a little sloppy. I adjusted the clips to fit the newer...

The assembly is not complicated, for each configuration I put exploded photos, pay attention to the insertion of the brass threads, (there are 2 models you need both), and to the direction of insertion, those placed in the attachment of the guides,...

If you think you want to change it or try to understand it feel free but I can't help.NOTES:Not all parts from this model need to be printed or even downloaded unless you want to alter the design or re-render the parts using the *.scad file. Parts...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...