branch 3d model free

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

They are both definitely WIP, I do not own a Orbiter V2 and are based on the CAD models. Update:18\10\21 Uploaded some 5010 fan ducts which are 8.5mm longer to allow for a Volcano Hot End. These are definitely WIP. I have not printed, installed or...

But the base design is a mix of: Ichibey's Sakura CoreCube Hbot modeling work Jetguy's lasercutter templates and electrical / extruder configuration DNewman's Sailfish programming for CoreXY gantries Credit should go to the above -- I'm just...

https://www.youtube.com/watch?v=Nn9B46IjsVU ______________________________________________________ ENGLISH ______________________________________________________ Only tested on T12-X, but can work on equivalent models with boxes of the same...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

FLSUN doesn't seem to be OK with the idea of sharing the CAD models (their loss...), so I didn't include the machine parts I reverse engineered (the effector is present though). The extruder is very crudely made, so I left it. How to build : ...

The firmware numbers will match regardless of your printer model. If you use a slicer that requires EEPROM, make sure to update your EEPROM settings to match your new firmware. The easiest part is printing the adapter plate - any ABS or PLA preset...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Print Settings Printer: FlashForge Rafts: No Supports: No Resolution: .2mm (Medium) Infill: 20% Doesn't matter Notes: For the most part, I intended these to print without supports; however, the housing is so wiggly that it needed some once I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

This is an second version of my first remix/modeling effort. Here is a <a href="https://www.thingiverse.com/thing:4714457">larger version that utilizes 4 magnetic bars</a>. <b>Principal changes in this remix:</b> <ul><li>In lieu of the...

Entry point for USB wire, hole has a separate part for covering it: + usb_wire_cover - base_bracket2_corner_RH x1 - base_bracket2_corner_RH_back x1 - base_cover_big x2 - base_cover_small x3 - base_cover_corner x2 * Front covers: base model is...

This is a 1:50 scale model (metric) of a space rocket that transforms into a Mars base. (well, conceptually) Instead of building vehicles to transport pieces to build a base, it seemed more reasonable to use the whole spaceship as the future...

(You may be able to get away with shorter bolts but these were the only ones I had that would fit) I have included a thumb screw model to make it easier to open and close the cover without a wrench. You will need an M3 heat insert but I cannot stress...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! Update 1: My Start and End G-codes in Cura working well with this firmware: ...

Any sagging of overhangs that occur at the very top/front of the model can simply be trimmed or cleaned away after. The mount can be either just press fit (if tight enough) or glued in place into the holes on the back of the body. I recommend gluing...

The COMPLETE Swamp Gurunda bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Swamp Gurunda (Presupported) The amphibious people of the swamps, with slimy skin and innate...

Note: I accidentally had two ⅔ marks on the outer ring in the original model. That has since been corrected but I haven't had a chance to print out a replacement, so the pictures still have the typo</p><h3>How to use</h3><p>Pick a measurement disk...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

First, I had to model the front of the display to accommodate the RepRap Discount Full Graphics Smart Controller and then I also decided it needed a back to protect the circuit board. Done... Then I decided to tackle the problem of mounting a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Originally designed for the Ender 3-V2 model, reusing the 4011mm Original axial Fan as Nozzle cooling. The original fan is loud, you will probably wish to change it with a quieter one and higher performance 4020 axial fan! Many options are available....

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the horizontality...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models) The small size and wide input voltage range of this unit make it ideal for operating Larson Electronics LED light bars, Golights and other equipment that requires 12VDC current...

... - Schematics:  Goggly eyes are optional, but they improve performance and friendliness of the finished project. Modelled using tinkercad & blender. ...

Make the adjustments, render the desired  STLs and print it! The models are in the position, they should be printed. No support is needed. ...I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this...

Post-Printing // model: Prusa i3 MK3 Y Chassis Bearing Straps // This replaces the zip ties that tend to stretch and can reduce accuracy over time. Optionally, also replace the entire strap and bearing with a 1-piece printed version that has been...