brake line straightener 3d models

Brake line tubing straightener

This is a model based on the park tool DT-2 disc brake straightener, useful tool if you have a bike with a compatible brake. ...:)

... up in my E3D clone. ... This straightener can either be attached using a Teflon tube or left unmounted. ...It comes equipped with high-quality 608 skate bearings and has the potential to be daisy chained, although I haven't had a chance to test it yet.

This is a 3/8 fuel line straightener. Tested with Aluminum tube and it works great. likely works with stainless or steel. Print 3 of these with PLA and assemble into a triangle looking thing. Use 17x40x12 bearings and wood screws to hold it...

So I created this cover/straightener, pretty much like a hexagonal drinking straw, that slides over the drip irrigation line to keep it straight (and also protected from damage such as solar UV and shovel nicks). I used a pentagonal design which...

<p>i recommend to print in from PETG for rigidity, it works well :)</p>

To ensure that your written content is properly aligned, you should use a straightener tool to correct grammatical errors and maintain clarity. This will help improve the overall quality of your writing and make it easier for readers to understand...

A device designed for straightening bent or misshapen steel bars, ensuring they maintain their intended form and function in construction projects. ...This equipment is essential for maintaining structural integrity and precision when working with metal...

Kawasaki KL Series Brake Line

Hydraulic brake line standoff to help route and secure brake lines. ... Made for 53mm USD forks

Simple bicycle brake line clamp designed to hold the brake line in place on frames that already support this style of brake line clamp.Print laying down and with 100% fill for best results.

Common bicycle clip that holds the brake line attached to the frame.

This is a clip that goes onto the a-arm to hold the brake cables of the Polaris Predator ATV. ... This replaces part #5435861 "Retainer, Brake Line, Front"

The essential tool for brake replacement, it blocks the brake fluid leak in the brake line. ...To assemble the tool, you will need two M8 nuts and two M8x45 or longer bolts.

Simple way to safely clamp a brake or fuel line.Hardware:M6 x 50mm full thread hex boltM6 nut

Replacement brake line clips for the engine bay. ...A full replacement is two double row and one upper and lower

I created this to hold the 3 SAE brake line wrenches I have, and make another one in blue for the 3 Metric brake line wrenches I have. ...I have the Duralast brake line wrenches.The walls are 4mm wide and the slots are 6.9mm, 6.5mm, and 6mm to hold the...

Model for 3D printing.You need to heat up the spiral a little bit to bend it up an insert the brake line. ...After that bend it back.

These are designed to replace old broken factory brake line holders on a 2016 Yamaha yz450f dirtbike, can not confirm fitment on anything other than 16' yz450f.

Model for 3D printing.You need to heat up the spiral a little bit to bend it up an insert the brake line. ...After that bend it back.

This is a super basic brake line clip to hold two lines close together. The Parametric tube clip was working, except for the opening, to actually clip the line into! ...I modified it with a simple bool to open the clip to tight (100 degrees open) and...

Decided to make a modified rear brake line guide for my 2000 KX 500. The line clips into the bracket and I made a notch to add a zip tie for some extra security. This replaces Kawasaki part # 13070-1144. ...Not sure of the durability, they made it...

This one printed as is should work with a standard 3/16 brake line nut and if you print it at 125% size, it should fit a standard 1/4 brake line nut. It is a tight fit so wrenches are required to put the nuts on but that means it won't get...

I'm upgrading my 2000 KX 500 with a custom rear brake line guide. The modified design clips seamlessly into place and incorporates a notch to secure a zip tie for added stability. ...This DIY upgrade replaces the original Kawasaki part number...

Human: Attaches .410 diameter brake line to sturdy 1.00 diameter front arms, securing it away from moving joints. Uses a robust 10-32 x 1.0 long socket head cap screw and a reliable 10-32 nylock nut. ...Specifically designed for the DF Goblin kit car,...

Decided to craft a custom rear brake line guide for my trusty 2000 KX 500. The line clicks securely into place within the bracket and I carefully crafted a notch to allow for an added zip tie, providing extra peace of mind against any potential wear...

This device secures the elongated brake hose in place yet permits its movement.

Here is a replacement part for your Weinmann brakes, if you have the ones that have barrel adjusters then you can find those on thingiverse as well, these should just slot in as they are same dimensions as the originals, I think the curved part isn't...

Here is a replacement part for your Weinmann brakes, if you have the ones that have barrel adjusters then you can find those on thingiverse as well, these should just slot in as they are same dimensions as the originals, I think the curved part isn't...