brain arteries 3d

My bot came with 410 mm Y rods, which is reflected in the Blender file, but this design should work on older printers with shorter rods (the original i3 had 330-335 mm Y rods). The .blend file depends on my standard parts/materials library, which can...

The servo spindle should be towards the middle of the robot.COGCut the servo horn with a pair of wire cutters so that it fits into the cogPush the servo Horn onto the cogMake sure the servo is at the minimum rotation position (turn it clockwise until...

If you want to add time indicators to the watchface I'd recommend using roman or greek statues holding the numbers, to fit the theme. UPDATE: I've added a few statues with numbers to make reading the clock a little easier, they are based on the...

It looks better when printed at that size.Print out and assemble with superglue.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

I present to you, what is likely one of the only mechanically working 3d-printed Prop Revolvers available, especially for free!Go here to see it in Operation: https://i.imgur.com/DBUVUkF.gifvIt is quite well balanced, see here:...

I've spent quite a bit of time getting to this design and I want to make it as accessible as possible so that as many people as possible can enjoy the greatness that is easy loading/unloading of the MMU. Good luck and enjoy!! Print Settings Printer...

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ ~...

Potřebné vybaveníNotebook nebo tablet, programy Tinkercad a PrusaSlicer, 3D tiskárna.Nepovinné - krabička čtvercových rozměrů, tvrdý papír, pravítko, tužka a nůžky (viz postup).9. Potřebné soubory a dokumenty (seznam...

Just to make it easier finding it all in one place.No support required.Diesel Generator you will need to superglue the bottom frame (very simple)Designed on...

These strips are bright enough I didn't notice only one was on. View from Octoprint Control tab during the first layer of my first print after installing. Print instructionsCategory: 3D Printer Accessories Summary Prusa i3 MK3 PiCam v2 X-Axis Motor...

Use with Right MMU2 Mount Z-Axis Top. Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15% GyroidSupports: Build plate onlyOpen 3MF files in PrusaSlicer for preconfigured settingsRequired hardware:Aluminum u-channel24V...

Here's a comparison picture by Hercules user techguychad: What to print: Print these files: hercules-1.7.2.stl hercules-dial-holder-1.3.stl hercules-belt-peg-1.2.stl hercules-fan-duct-1.3.stl bmg-handle-short-1.0.stl...

... layers, 60° bed temperature, outside perimeters first.  I turned the model 35° anticlockwise, then set the seam position to ‘rear’.  The texture on the side panels comes from this textured bed plate, and I used the Tecbears black PLA.

Violence is never more than a heartbeat away.Use those guns! Deliver your cargo!Stay in the fight!Nothing to glue.Stand up your Space Port before it's too late!Designed on...

Avoid lifting and warped prints!Print all three parts (body, treads, roof option.)Superglue the treads to the body.Choose the roof option and glue, or leave it free and swap it out as needed!Superglue works best for gluing it together.It will scale...

Remove the stock z-axis tops and replace with this light bar mount.Dual Mount Z-Axis Top No Switch: Same as Dual Mount Z-Axis Top with no hole for the power switch.  Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill:...

Use thread lock to ensure these will not accidentally come loose.A 36mm diameter propeller should run freely inside the rudder at all rudder angles.Mount the rudder support to the hull using M3x6mm screws.Then put another M3x6 screw to secure the...

His diagrams and commentary on escapement efficiency were excellent, however. I only discovered this write up on escapement design after I'd finished, but it would also be a useful head start for anyone interested -...

I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). Material: ABS, 3mm thick Nozzle: arcol.hu hotend v4.1.1, 0.35mm diameter Printer: DIY...

... at 0.2 layer height.</p> <p>But once you've raised the limits, it's worth seeing what a 350mm/s travel move really looks like at 5500 or 6000 mm/s^2. (Answer: sorta scary, honestly) Designed from scratch in SketchUp. Category: 3D Printer Accessories

Remove the stock z-axis tops and replace with this light bar mount.Single Mount Z-Axis Top No Switch: Same as Single Mount Z-Axis Top with no hole for the power switch.&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15%...

(That's something else, sorry.)Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

Here's a comparison picture by Hercules user techguychad: What to print: Print these files: hercules-1.7.2.stl hercules-dial-holder-1.3.stl hercules-belt-peg-1.2.stl hercules-fan-duct-1.3.stl bmg-handle-short-1.0.stl...

Avoid lifting and warped prints!Print all three parts (body, cab, treads)Superglue the treads to the body.Superglue the cab to the body.Superglue works best for gluing it together.It will scale easily if you want a larger or smaller...

Clogs are a thing from the past and no more grinded up filament stuck in the gear.Here's a comparison picture by Hercules user techguychad:What to print:Print these...

With external markings and without.Stand up your Space Port before it's too late!Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under...

How to make your own module for the phone holderIf you know how to use 3d designing software here are the dimensions to make your very own module for the Modular Phone Holder! All the modules use a very basic system: to start, the main rotating part...

If do you need to get the lock back off, the best way I found was to stick long allen keys into both of the lock's holes and then pinch them together to lever the lock slightly apart, which reduces the pressure enough that you can wedge a thin...

Worlds are waiting.&nbsp;Designed on Tinkercad.Enforced supports are required on overhangs and the main bodies (see 3mf files).The main bodies can be glued together to create longer Cargo Pods.Super glue everything together.Start shipping cargo; the...

(The tweeter assembly on the speaker is moveable to fine-tune its direction, and this clearance accommodates the assembly even at its most extreme angle of direction).Tools NeededIn addition to your 3D printer and whatever miscellaneous tools you'll...