boxer at rest 3d models

This probably isn't for the faint of heart and I doubt anyone is crazy enough to try printing this but I still thought I'd post it because someone might be able to use parts of it (the coin slide mechanism?) or maybe at least get ideas from it. The...

If you are using Grbl this is probably an easier task, but I am not familiar with how that works.If you want to use Grbl firmware with this using an arduiono Uno or similar board, I would suggest looking at the guide with...

Offers some new features (see below).Many thanks to Ryan at V1 Engineering for his design genius and gracious generosity in sharing his work with us all. For those whose LowRider v3 MPCNC has or will have a BTT SKR Pro 1.2 main board and a BTT...

The available sizes (and corresponding tool bit capacities) are shown below: Cell Approx Width OAL Capacity cm in (tool bits) 10 20 8 80 16 27 11 128 20 32 13 160 22 35 14 176 Note that the indicated capacities are nominal, as some tool bits may...

INSTRUCTIONS -------------------------------------------------- For the most part it's pretty much common sense where the pieces go and can tell just by looking at the pictures I have uploaded. (I'll clean up and get better pictures soon.) I have a...

clean up the edge so no flakes of material remain at the edge and interfere with the installation later.Install the clock crystalremove the inside protective film.Assemble the clock internalsSnip the support structures from the chapter_ring.Install...

... remix my ideas. If this has gotten you thinking considering Sharpie mods more carefully like it did for me, consider liking the design,  leaving me a tip using the button at the top-right and subscribing to my designs here.Reference Scans

I created this grommet to protect and guide them as well as clean up the look. https://www.thingiverse.com/thing:3451429 The ptfe tubes then enter the lack enclosure and are held in place using this design and some pc4-m10 fittings....

So I can keep my printer off all the time while my Pi Zero 2 is always on (consuming minimum amount of power) keeping the printer ready for action at any time. The fans are off while the main PSU is off (relay in off position). The 5V PSU does not...

This will cause surface irregularities when printing because filament pressure at the nozzle will be irregular. The wiring colors on various Stepper motors are not consistent. Below is the easiest way I found to get the wiring sorted...

Don't forget to first insert an M5 nylock nut into the capture slot on the new stub-right. Reinstall the lead screw on the right side assembly.If needed, reinstall your LR Core. Re-run the wiring for the end stop switch, and reattach the X belt (now...

Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: bar_length_trim = 0 lug_text_distance = 2 outer_margin_width = 1 ruler_unit = 10 barextruder = extruder1 lug_width = 5...

A magnet moving with the vane triggers one, two, or three at a time. The two trigger situation in particular allows deriving 8 additional positions, resulting in 16 overall. So we do not only get N, NE, E, SE, S, SW, W, NW, but NNE, ENE,...

UHU Allzweckkleber)Tools:   1x cardboard cutter   1x straight cutting guide    1x hexagon spanner   1x 8mm wood drill + portable electric drillSteps of Assembly: 1) Print parts:   4x...

Now, the waters are not safe, and the people are worried once again. Behold, theDinosaurs All The Way Down insert designed to hold all the game pieces for both Dinosaur Island and the expansion -- Totally Liquid (TL)! This gets a little complicated...

The gear should rotate freely -there should be no stiffness or catching on any part of the rotation.Ensure the gear is rotated so all the slots in the driven gear (4) are tested.The clock will stop at random if the rotation is not 100%...

If you have a printer, then you have such electronics! PaScn3D connection to Prusa 3D printer in a minute (tested!) – dedicated mounting brackets, components adapted to the dimensions of the device Modularity – adaptation to other printers without...

Perfect for preppers as at some point in the apokalyptic future the original batteries wont be available for purchase anymore XD Only downside is that the battery pack will “shutdown” once one battery is taken out. Means when you insert batteries...

Offers some new features (see below).Many thanks to Ryan at V1 Engineering for his design genius and gracious generosity in sharing his work with us all. For those whose LowRider v3 MPCNC has or will have a BTT SKR Pro 1.2 main board and a BTT...

Let's take a closer look at some of its key features and see if it lives up to the hype. One of the standout features of the ROG Strix XG438Q is its high refresh rate. With a refresh rate of 144Hz, this monitor can handle fast-paced games with ease,...

Our original nose was printed using a 'standard' setting and weighed in at 50 grams. The new nose weighs in 39.4 grams. The model has been built, with the fins filled and an initial coat of grey primer. The weight of the rocket without the...

 The upper_band does not wrap the  upper_mid around at the back to make room for the hinge on the lower_band.  Make sure that the overhang on the upper_band is on the same side as the two holes in the middle of the upper_mid (where the hasp will...

Two per strut are required at the front and rear. Alternatively, use springs 30mm x9mm x0.9mm, here only one spring is required per shock absorber. Update 23_12_2020 I uploaded the model "Zahnrad_18_23_neu", which I had forgotten. Thanks...

3 walls for bando bashing.Infill: Use 20 - 30% cubic infill15 - 20% for most setups25 - 30%  infill for bando bashingReally don't go above 30% infill, it just adds extra weight but no strength benefit.Also look at the makes section for other users'...

This will require you to stop the print just at the right time and insert the magnets before continuing. small fix for LidMagnetPosition where incompatible lid magnet holes had been created for the actual lid 2019-01-03 Version 2.5 Adjusted...

As for the cut itself - in principle, I could cut each of these materials in one pass at a slow speed, but the cut quality is much cleaner, if you make two or more passes at a higher speed, then the edge is cleaner. On the laser head seller's page...

Before that, I had no experience with him in work, although I often made orders for cutting and engraving at enterprises specializing in this process. I mastered it in a day, everything turned out to be quite simple, but the alignment of the...

(z)Orbiter 2.0 Extruder Lite with RHD Fan Duct and optional Rigid Mounting for the TL Dragon Hotend for One-Handed Nozzle Changes This is a remix of the ZOrbiter V1.5 Geared Extruder by ZARIBO (the CAD files for ZARIBO's own V2.0 extruder aren't...

The lamp is T5 temperature rated, Design Lights Consortium approved, and the LED light head retains 80% of its lumen output after 60,000 hours of use, far longer than incandescent or fluorescent lamps.Beam Angles: When used as a fixed mount fixture,...

I am printing the door and base in the vertical orientation both for strength of the parts and to minimize supports needed. Re-ARM-fan-endpiece.stl Re-ARM-face-endpiece.stl Printed in a flat orientation with the flat side down (the side with the thin...