bot model

Test Print Video here: https://www.youtube.com/watch?v=H8vL2GeMYMQ Previous version here: https://www.thingiverse.com/thing:4650517 As per the previous version a big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken...

 Note, only model files (.AMF) are uploaded, no g-code uploaded for the upgrade.This is a redesign of the MMU2S Print buffer system to relocate the 5 spools above the printer and a rear mounted vertical buffer system. It saves a lot of space, fitting...

Enable the Rotate_For_Printing option to rotate the part in this orientation. Supports: Depending on the options selected, it may be necessary to use supports. Rafts: Doesn't Matter License The "Sidewinder X1 FFC Riser" models (.stl) are licensed...

It removed the support, but also broke the model. Before I removed support from the second trolley I drilled out the majority of the support going through the assembly hole with a large drill bit. After drilling, the removal trick on a vise worked...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

The solution is simple enough: Both parts of the model need to be placed away from the centre point (still properly lined up with one another, obviously), so that the probe can do its thing without the first print getting in the way. So began attempt...

http://www.thingiverse.com/thing:83952 The specific parts that I have modeled so far are: Cross Tie: This is the part that holds the two rails at the proper distance apart, and is what other pieces attach to. Base: A flat plate with holes in it. I...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

There seem to be quite some error margin in production, if your model is a bit too big to fit, just sand off maybe .5 mm from the sides to make it fit.Completely(!) remove any filament remains inside the two enclosure parts.Fit servo into upper half...

Specifically, the mouth utilizes inexact measurements, and inconsistencies in source models from the 3D printing process made it difficult to gain a good measurement. On the sketch, we measured the mouth to be 1.20cm from the side of the constraint...

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

Keep weight and cooling considerations in mind if using an alternate - ESC: Water proof ESC appropriately rated for your motor / battery combo - Cooling Nipple: M4 X L15 https://www.aliexpress.com/item/32614416689.html - Cooling Tube: 4 mm I.D 7 mm...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

To split it with ease, right-click on your model within Cura. When preparing your parts for printing, make sure flat sides are aligned downward. For a smoother print process, consider setting 0.1mm layer height and 40% infill as defaults. Here is...

Works with the regular rectangular heat sinks or the Waveshare heat sink.Two different styles of ventilation openingsSTEP files available for easy remixingThis remix does not currently have an option to mount a fan inside the enclosurePowering the...

2x 3D printed pulley wheels 2x (or 4x) 3D printed conduit couplers (depending on how you are doing the conduit) 2x 3D printed wing push brackets (based on your plane model) (For any non-symmetrical push brackets, you'll need to print a mirror...

The attached model is sized to fit the Eye Cu Smile V2 and V1 filter housings at 45 mm OD and 10.5mm high However if you want to make any size antimicrobial / antiviral filter meshes for any purpose then even sketchup will suffice Steps to draw a...

Two B2s stacked works well for going higher.Related Links: Magnet Insertion Tools for Bases Drilling Guide and Magnet Insertion Tools for Walls Door Frame Adapter for rbross DoorsCompatibilityThe short tiles (Row A and Column 1) are also compatible...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

One intersting thing I probably should have done, is just print the columns on the platforms, would have saved some time, and the hardest assembly step. Next Acquire the Electrical components: Electrical Components Post Printing is very involved,...

The COMPLETE Order of the Labyrinth bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The strong Minocs of the Order of the Labyrinth are the descendants of Tesevros the Wise,...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models). If you purchase this transformer with any of our Larson Electronics lights, we will make sure that the connectors are a match.Wiring/Plug: This waterproof power supply is...

Please check the images to see what it is included in this kit.This set contains: - Noble Alfar Knights (12)- Goldhorn Cervid Riders (4 + 4)- Seraphion – the Lustrous Flame- Eliora – the Dawnbringer- Lythalia – the Whisper of Secrets- Elthorion –the...

It can be thrown whole into a filament dehydrator to refresh the packets, without worry of warping. Assembly: Attach the bearings to the end of the rollers and snap them into the slots in the base (Optional, Glue them to the spindle so they won't...

the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic instead. Ive uploaded a reinforced version of the arm that should work better with heavier controllers.i also opened up the...

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...

Downloaded some Radio Control model yacht designs. Non of them suited my fancy for building, so I decided to come up with my own. Main Desing principles... No Keel! -> Surf Board / Windsurfer style. Light Weight (relative to size of jib!) ...

The code is a bit messy (especially for the rack), but it should work for most reasonable settings. This way you can also increase the resolution of the 3D models, Due to size constraints they had to be rendered a bit low. Using this bash script you...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...