bose 3d

<p>There is a recession in the center of the shelf to fit the protrusion in the bottom of the SoundLink that needs supports; print it with the screw holes facing down. I used PETG, but PLA should work fine. ...The screw holes are sized for screws with...

I'm building a compact holder for my remote control that always seems to vanish into thin air. To start, I downloaded the logo STL file from https://www.thingiverse.com/thing:1815570. Next, I attached double-sided tape to the back and secured it...

During Homeoffice I started using my headset with a softphone instead of hardware desk phones. But I had complaints, that my voice was too soft so I started holding the microphone towards my mouth, which was much better. Then I designed a...

Remixed from thing:4703279, added a clip. ...However it's quite difficult to print with an FDM for now

Printed Sideways in PETG but i think PLA will also be fine 3mm Wood Screws

<p>At the call center where I work we use old VXI microphone headsets. They're a discontinued model, but even if they were still selling new ones the deluxe one used to be $70. After 8 hours the little foam pads they come with might as well be...

Will report back with a usage report - So far all seems solid enough and loud enough at low speed. ...When the rev's are up the exhaust takes over anyway!

I'm looking for a sturdy hook or mount to secure my 19mm bed head shield in place. Using two 20mm components works well, but I think a 130mm option would be even better. When designing this piece, I initially focused on the overhangs, not considering...

They stood there silently, two figures locked in a moment of mutual understanding. Their eyes met and held, a spark of recognition flashing between them like a fleeting firefly on a summer night. It was as if time itself had slowed down, allowing...

Wall Mount Holder for Lifestyle Remote Control - Perfect Fit for Your 38/48 Model. ...Designed Specifically for Remotes Without a Display Screen, This Mount Keeps Your Remote Secure and Within Easy Reach at All Times.

Requires one 2" 8-32 screw & nut when assembled.

This design was crafted using Tinkercad's powerful tools, allowing for real-time editing and collaboration. ...You can instantly access the live version here: https://www.tinkercad.com/things/cJzmP6zs3aU

This is only a quick and dirty merge of the two referenced models.I needed something quick, bc OMG this Jabra on-ear were hurting!CushionsBose QC Replacement Ear Pads from "Krone" on Amazon (about ~8€), but I guess the brand does not matter.. ...add two...

Hook or mount for a 19mm bed head shield thing. 2x 20 mm works fine but the 130 mm could be nicer :D I did not think of the bridges when I designed it only of the overhangs and when I printed the 130 mm version it turned out that it looks nice and...

With this print you can mount the Volume control to one of the Speakers like the older version but better. ...To Mount it just use double sided tape.

Add a mic and cable, and this will snap onto your QC35 II headphones and provide a secure wired boom microphone connection.

This thing is a remix to separate each piece into a single STL file. I dont have any right on these pieces. ... Remixed from: https://www.thingiverse.com/thing:2268106

I quickly cobbled together this temporary solution in one evening, relying on rough estimates after the extremely fragile ear cup components broke off. Print 100% infill. A more refined version will be coming soon. ... Edit: Looks like I didn't need...

<p>I have replace my airplane connector for a extra battery holder.<br/> Now i can take a total of 3 batteries!!</p> <p>Please DONATE if you like!</p> <h3>Print instructions</h3><p>Category: Audio</p>

I remixed the Power Switch Replacement by SamFLoppy because i wanted to have the original IEC 60417-5009 Power On-Off Standby Symbold on the cap. Also i´ve added two small circled dents left and right (left side must be closer to the center) so...

---Update---21 October Now printed, tested and proven to fit seamlessly with the genuine leather case over a 6plus. See Photos for clarity and understanding. Conceived at the behest of a user who sought to pair their clip designed specifically for...

<p>Inspired by the model “Wall shelf for speakers” by Arkadiy01. &nbsp;Resizing the original could have worked but remixing allowed me to make a few modifications. &nbsp;I added a 2nd screw hole, moved the angled side brackets in line with the back...

The Delco Radio Emblem, a Custom Design for the C4 Corvette's Upgraded Audio System, Falls Short of Its Printing Goals Due to Technical Limitations of the Current Hardware. ...Future Refinements in Software Engineering Might Pave the Way for Its...

Got a Solo 5 and remote with no back / battery door/cover. Designed a simple replacement battery door. I welcome comments, this door fits my remote perfectly, however, by the 5th revision, my remote had some wear in the locking mechanism, so your...

This model was designed using Tinkercad's advanced features. ...Make changes directly on the web at https://www.tinkercad.com/things/7tiBxqKS2wj.

Viscous hexagonal nut with an M6 X 30 thread. ... Instructions for printing with a zortrax M200 ABS plastic, settings at .14 mm resolution, using a 20% infill density setting.

I've replaced my airplane's charging port with an extra battery holder, giving me the ability to carry three batteries at once. This upgrade has greatly enhanced my flying experience and I'm thrilled to share it with fellow enthusiasts. ...If you...

User: Set printer to 20% fill density, .2mm layer thickness. ...Generate supports solely under headphone base model.